Dell Unity XT 480 Unity All Flash and Unity Hybrid Unity 480/F Unity 680/F Uni - Page 96

Transfer parts from the faulted SP assembly to the replacement SP assembly

Get Dell Unity XT 480 PDF manuals and user guides View all Dell Unity XT 480 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 96 highlights

Figure 114. Removing the top cover Transfer parts from the faulted SP assembly to the replacement SP assembly Transfer the following components from the faulted SP assembly to the corresponding locations in the replacement SP assembly. To help ensure the correct placement in the enclosure, transfer only one component at a time. ● Transfer the power supply ● Transfer the I/O module and fillers ● Transfer the embedded module ● Transfer the internal M.2 boot module ● Transfer DIMMs ● Transfer internal fans ● Transfer the internal battery backup module Remove the internal battery backup module Steps 1. Remove the internal battery backup module cover. 2. Disconnect the internal battery backup module cable from the motherboard by squeezing the white tab and lifting upward. 3. Push down on the two blue retaining tabs. At the same time, pull up on the blue pull tab. 96 Service Procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
Figure 114. Removing the top cover
Transfer parts from the faulted SP assembly to the replacement
SP assembly
Transfer the following components from the faulted SP assembly to the corresponding locations in the replacement SP
assembly.
To help ensure the correct placement in the enclosure, transfer only one component at a time.
●
Transfer the
power supply
●
Transfer the
I/O module
and fillers
●
Transfer the
embedded module
●
Transfer the
internal M.2 boot module
●
Transfer
DIMMs
●
Transfer
internal fans
●
Transfer the
internal battery backup module
Remove the internal battery backup module
Steps
1.
Remove the internal battery backup module cover.
2.
Disconnect the internal battery backup module cable from the motherboard by squeezing the white tab and lifting upward.
3.
Push down on the two blue retaining tabs. At the same time, pull up on the blue pull tab.
96
Service Procedures