Dell Unity XT 480 Unity All Flash and Unity Hybrid Unity 480/F Unity 680/F Uni - Page 46

Rebooting a SP assembly into Normal Mode, Installing the embedded module

Get Dell Unity XT 480 PDF manuals and user guides View all Dell Unity XT 480 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Figure 43. Installing the embedded module 2. When the embedded module is fully seated, push the release lever back into the system until the orange tab locks the lever in place. Figure 44. Locking the release lever 3. Connect each cable into the same port from which it was removed. Rebooting a SP assembly into Normal Mode Prerequisites Ensure that the replacement I/O module, embedded module, or 4-port card has been correctly installed using Unisphere. The replaced part's status indicates that the module is powered off and will power on during the next system reboot. About this task Reboot the recently serviced SP assembly into Normal Mode using the procedure that follows: Steps 1. Open Unisphere and select Service, then Service Tasks. 2. Under the name of the storage processor where you installed the new I/O module, embedded module, or 4-port card, select Reboot and click Execute. 3. When prompted, type the Service Password to put the SP assembly into Normal Mode. It may take up to 15 minutes for the system to complete its reboot to return to normal mode. 46 Service Procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
Figure 43. Installing the embedded module
2.
When the embedded module is fully seated, push the release lever back into the system until the orange tab locks the lever
in place.
Figure 44. Locking the release lever
3.
Connect each cable into the same port from which it was removed.
Rebooting a SP assembly into Normal Mode
Prerequisites
Ensure that the replacement I/O module, embedded module, or 4-port card has been correctly installed using Unisphere. The
replaced part's status indicates that the module is powered off and will power on during the next system reboot.
About this task
Reboot the recently serviced SP assembly into Normal Mode using the procedure that follows:
Steps
1.
Open Unisphere and select
Service
, then
Service Tasks
.
2.
Under the name of the storage processor where you installed the new I/O module, embedded module, or 4-port card, select
Reboot
and click
Execute
.
3.
When prompted, type the Service Password to put the SP assembly into Normal Mode.
It may take up to 15 minutes for the system to complete its reboot to return to normal mode.
46
Service Procedures