Dell Unity XT 480 Unity All Flash and Unity Hybrid Unity 480/F Unity 680/F Uni - Page 55

Remove a 4-port card, Install a 4-port card

Get Dell Unity XT 480 PDF manuals and user guides View all Dell Unity XT 480 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

Remove a 4-port card Steps 1. Remove the SFPs from the front of the embedded module. 2. Remove the air dam at the front of the embedded module by loosening the four captive screws. 3. Push down the two blue tabs on the back of the 4-port card to release the 4-port card. Figure 54. Opening the retaining tabs 4. Lift the 4-port card off the pegs, and pull the 4-port card away from the embedded module. Figure 55. Removing the 4-port card Install a 4-port card Steps 1. Align the 4-port card in the embedded module so that the ports on the front line up with the slots on the front of the embedded module. 2. Align the white pegs beneath the holes on the 4-port card. CAUTION: Do not force the 4-port card into place. If the 4-port card does not smoothly seat, re-align the pegs and try again. Service Procedures 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
Remove a 4-port card
Steps
1.
Remove the SFPs from the front of the embedded module.
2.
Remove the air dam at the front of the embedded module by loosening the four captive screws.
3.
Push down the two blue tabs on the back of the 4-port card to release the 4-port card.
Figure 54. Opening the retaining tabs
4.
Lift the 4-port card off the pegs, and pull the 4-port card away from the embedded module.
Figure 55. Removing the 4-port card
Install a 4-port card
Steps
1.
Align the 4-port card in the embedded module so that the ports on the front line up with the slots on the front of the
embedded module.
2.
Align the white pegs beneath the holes on the 4-port card.
CAUTION:
Do not force the 4-port card into place. If the 4-port card does not smoothly seat, re-align the
pegs and try again.
Service Procedures
55