Dell Unity XT 480 Unity All Flash and Unity Hybrid Unity 480/F Unity 680/F Uni - Page 50

Install an embedded module, Adding the 4-port card to SP B, Steps, About this task

Get Dell Unity XT 480 PDF manuals and user guides View all Dell Unity XT 480 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

6. Install the air dam that came with the 4-port card, and tighten the four captive screws. 7. If the 4-port card includes SFPs, install them into the embedded module. Install an embedded module Steps 1. Align the embedded module with the empty slot and carefully push it into the slot. As the embedded module is installed, the release lever rotates inward. Figure 49. Installing the embedded module 2. When the embedded module is fully seated, push the release lever back into the system until the orange tab locks the lever in place. Figure 50. Locking the release lever 3. Connect each cable into the same port from which it was removed. Adding the 4-port card to SP B About this task You have completed the addition of the 4-port card to SP A. Now you are ready to add the other 4-port card to SP B by repeating the tasks that you just performed for SP A. 50 Service Procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
6.
Install the air dam that came with the 4-port card, and tighten the four captive screws.
7.
If the 4-port card includes SFPs, install them into the embedded module.
Install an embedded module
Steps
1.
Align the embedded module with the empty slot and carefully push it into the slot.
As the embedded module is installed, the release lever rotates inward.
Figure 49. Installing the embedded module
2.
When the embedded module is fully seated, push the release lever back into the system until the orange tab locks the lever
in place.
Figure 50. Locking the release lever
3.
Connect each cable into the same port from which it was removed.
Adding the 4-port card to SP B
About this task
You have completed the addition of the 4-port card to SP A. Now you are ready to add the other 4-port card to SP B by
repeating the tasks that you just performed for SP A.
50
Service Procedures