Dell Vostro 1510 Service Manual - Page 16

Display Bezel - hard drive replacement

Get Dell Vostro 1510 PDF manuals and user guides View all Dell Vostro 1510 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

11. Lift the display assembly out of the computer. 1 display cable 2 antenna cables 3 display assembly Replacing the Display Assembly CAUTION: Before you begin the following procedure, follow the safety instructions that shipped with your computer. This procedure assumes that you have completed the removal procedure Removing the Display Assembly. 1. Align the display hinges with the holes in the base of the computer, then lower the display into place. NOTICE: Ensure that the display cable and antenna cables are properly routed and secured beneath the plastic tabs on the palm rest. 2. In sequential order, replace the four M2.5 x 5-mm screws into the base of the display assembly. 3. Route the display cable and antenna cables beneath the plastic tabs on the palm rest. 4. Slide the antenna cables through the hole in the palm rest and the base of the computer. 5. Connect the display cable to the display cable connector on the system board. 6. In sequential order, replace the four M2.5 x 5-mm screws in the base of the display assembly. 7. Replace the keyboard (see Replacing the Keyboard). 8. Replace the hinge cover (see Replacing the Hinge Cover). 9. Close the display and turn the computer upside down. 10. Replace the M2.5 x 8-mm screw that attaches the display assembly to one corner of the computer. 11. Replace the WLAN card (see Replacing a WLAN Card). 12. Replace the hard drive cover. See Removing the Hard Drive for an illustration of the hard drive cover. Display Bezel

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
11.
Lift the display assembly out of the computer.
Replacing the Display Assembly
This procedure assumes that you have completed the removal procedure
Removing the Display Assembly
.
1.
Align the display hinges with the holes in the base of the computer, then lower the display into place.
2.
In sequential order, replace the four M2.5 x 5-mm screws into the base of the display assembly.
3.
Route the display cable and antenna cables beneath the plastic tabs on the palm rest.
4.
Slide the antenna cables through the hole in the palm rest and the base of the computer.
5.
Connect the display cable to the display cable connector on the system board.
6.
In sequential order, replace the four M2.5 x 5-mm screws in the base of the display assembly.
7.
Replace the keyboard (see
Replacing the Keyboard
).
8.
Replace the hinge cover (see
Replacing the Hinge Cover
).
9.
Close the display and turn the computer upside down.
10.
Replace the M2.5 x 8-mm screw that attaches the display assembly to one corner of the computer.
11.
Replace the WLAN card (see
Replacing a WLAN Card
).
12.
Replace the hard drive cover. See
Removing the Hard Drive
for an illustration of the hard drive cover.
Display Bezel
1
display cable
2
antenna cables
3
display assembly
CAUTION:
Before you begin the following procedure, follow the safety instructions that shipped with your computer.
NOTICE:
Ensure that the display cable and antenna cables are properly routed and secured beneath the plastic tabs on the palm rest.