Denon AVR-3312CI AVR3312CI_OwnersManual - Page 126

Basic version Advanced version 6 Pressing ui, select the first letter of the device brand name. Then press ENTER. REMOTE SETUP GUIDE Please select the first letter of 1 the brand name of the device. A B C D E Device : DVD F G H I Select Enter RETURN Return • The first character is displayed as 1, A to Z. (Initials for the brand are displayed for each category.) For brand names that start with numbers and symbols, select "1". 7 Pressing ui, select the device brand name. Then press ENTER. REMOTE SETUP GUIDE Please select the brand name. Dantax Denon Disney DSE Durabrand -DVD- Select Enter RETURN Return • When there are several pages of brand names, the pages can be switched by pressing the remote control unit's CH + or CH -. NOTE If the desired brand name is not listed, the supplied remote control unit cannot control the device. Use the remote control unit supplied with the device to be used. 8 The procedures for registering remote control codes and remote control preset registration are displayed. REMOTE SETUP GUIDE Device Brand Code [1/3] : DVD : DENON : 30490 1. Press [INPUT SOURCE]. 2. Press and hold [DEVICE ON ( l )] for 3 seconds. 3. Input code with [0-9]. 4. Press any key to check device. (e.g. [DEVICE ON ( l )]) OK QUICK1 NG QUICK2 QUICK3 Return Press QUICK 1 if device works, QUICK 2 if not NOTE If a wrong brand name is selected, press QUICK SELECT 3. The following screen is displayed: REMOTE SETUP GUIDE Device : DVD Brand : DENON Code [1/3] Press: 3[A04M9P0] button. 1. Press [INAPnUdTpSreOsUsR[ECNET].ER] button to return 2. Press anBdrahnodldse[lDecEtVmICeEnOu.N ( l )] for 3 seconds. 3. Input code with [0-9]. 4. Press any key to check device. (e.g. [DEVICE ON ( l )]) OK OK QUICK1 NG QUICK2 QUICK3 Return Press QUICK 1 if device works, QUICK 2 if not Press AMP then ENTER to return to step 7. 9 Press the input source button on which the preset code is to be registered (BD, SAT/CBL, TV, DVD, V.AUX, DOCK, GAME1, GAME2 or CD). • For TV, only the preset code for the categories "TV", "TV/DVD", or "TV/VCR" can be registered. 10 Press and hold ZONE/DEVICE Z for at least 3 seconds. The zone mode indicator flashes twice. Registering preset codes 11 Enter a five-digit code using 0 - 9. Press the buttons with an interval less than 10 seconds. REMOTE SETUP GUIDE Device Brand Code [1/3] : DVD : DENON : 30490 1. Press [INPUT SOURCE]. 2. Press and hold [DEVICE ON ( l )] for 3 seconds. 3. Input code with [0-9]. 4. Press any key to check device. (e.g. [DEVICE ON ( l )]) OK QUICK1 NG QUICK2 QUICK3 Return Press QUICK 1 if device works, QUICK 2 if not • When the code is registered. The zone mode indicator flashes twice. • When the code is not registered correctly The mode indicator slowly flashes once. Perform from step 9 again. • When an input number is not correct Press ON once then perform the operations from step 9 again. 12 Operate the device being used to check the operation. • If the device is operating, press QUICK SELECT 1. Go to step 13. • If the device is not operating, press QUICK SELECT 2. Go to step 14. 13 The screen shown below is displayed, and registration of the preset code is completed. REMOTE SETUP GUIDE Device : DVD Brand : DENON Code [1/3] Rem:o3te04S9et0up Guide is finished. 1. Press [INPUT SOURCE]. 2. Press anPdrehsos l[dAM[DPE]VbIuCtEtoOnN. ( l )] for 3 seconds. 3. Input coAdnedwpirtehss[0[-E9N]T. ER] buton to return 4. Press anMyEkNeUy. to check device. (e.g. [DEVICE ON ( l )]) OK OK QUICK1 NG QUICK2 QUICK3 Return Press QUICK 1 if device works, QUICK 2 if not • The menu screen is retrieved. Press AMP then ENTER. vSee overleaf Information 123