Denon AVR-3312CI AVR3312CI_OwnersManual - Page 149
Symptom, Cause/Solution, Check that Speaker Config. - Front Height or Front Wide is
UPC - 883795002042
View all Denon AVR-3312CI manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 149 highlights
Basic version Advanced version GAudioH Symptom Audio is not output. No sound is produced from surround speaker. No sound is produced from surround back speaker. No sound is produced from front height speaker. No sound is produced from subwoofer. Cause/Solution Page • Check the connections for all devices. C 3, 8, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19 • Check the speaker connections and configurations. C 6, 63, 64, 65, 66, 67 • Check whether the audio device power is turned on. - • Adjust the master volume. 29, 83 • Cancel the mute mode. 29, 83 • Select a suitable input source. 28, 83 • Select a suitable input mode. 94 • Disconnect the headphones. No sound is output from the speakers 128 or the PRE OUT connectors when headphones are connected. • Check if the surround speakers are connected to the SURROUND - terminals. • Check if "Amp Assign" is set appropriately in order to output 105 audio from the surround back speakers. • Set "Speaker Config." - "Surr.Back" on the menu to something 106 other than "None". • Set "Surround Parameters" - "Surround Back" on the menu to 99 something other than "OFF". • Set the surround mode to something other than "STEREO" and 55 "VIRTUAL". • Set "Surround Parameters" - "PLgz Height" on the menu to 99 "ON". • Check if "Amp Assign" is set appropriately in order to output 105 audio from the front height speakers. • Set "Speaker Config." - "Front Height" on the menu to something 106 other than "None". • Check the subwoofer connections. C 6, 63, 64, 65, 66, 67 • Turn on the subwoofer's power. - • Set "Speaker Config." - "Subwoofer" on the menu to "Yes". 105 • If "Front" and "Center" for "Speaker Config." are set to "Large", 105, 106 and "Subwoofer Mode" is set to "LFE", no sound may be output from the subwoofers, depending on the input signal or selected surround mode. Symptom DTS sound is not output. Dolby TrueHD, DTSHD, Dolby Digital Plus audio is not output. Dolby PLg mode or DTS NEO:6 mode cannot be selected. Audyssey DSX™ cannot be selected. Audyssey MultEQ® XT, Audyssey Dynamic EQ® and Audyssey Dynamic Volume® cannot be selected. Dynamic EQ® and Dynamic Volume® cannot be selected. RESTORER cannot be selected. Cause/Solution • Set "Decode Mode" on the menu to "Auto" or "DTS". • Make HDMI connections. • Check that "Speaker Config." - "Center" or "Surround" is set to other than "None". If the speaker system is 2.0/2.1ch, this surround mode cannot be selected. • When headphones are used, Dolby PLg or DTS NEO:6 cannot be selected. • Check that "Speaker Config." - "Front Height" or "Front Wide" is set to other than "None". • Check that "Speaker Config." - "Center" is set to other than "None". • Switch the surround mode to STANDARD. • When headphones are used, Audyssey DSX™ cannot be selected. • Switch the surround mode to other than "DIRECT" or "PURE DIRECT". • When headphones are used, MultEQ® XT, Dynamic EQ® and Dynamic Volume® cannot be selected. • Run Audyssey® Auto Setup. • Check that an analog signal or PCM signal (fs=44.1/48 kHz) is input. For playback of multichannel signals such as Dolby Digital or DTS surround, RESTORER cannot be used. • Switch the surround mode to other than "DIRECT" or "PURE DIRECT". Page 94 8 105 - 106 105 55 - 55 - 21, 68 103 55 Information 146