HP 226593-B21 Smart Array 5i Plus Controller and Battery Backed Write Cache En - Page 30

Updating the System Partition, Enter, Caution

Get HP 226593-B21 - Smart Array 5i RAID Controller PDF manuals and user guides
UPC - 720591665913
View all HP 226593-B21 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Updating the Controller Firmware - If the screen message reads as follows, press the Enter key, and then go to step 8 of these instructions: The ROM image files found for the device selected are not newer than the current ROM image - If the ROM firmware currently on the controller is older than that on the Options ROMPaq diskette, then the screen message reads as follows: Device to reprogram: All Compaq Smart Array nnnn Controller(s) Controller(s) Current ROM revision: Compaq Smart Array nnnn Controller x.xx Select Firmware Images: Compaq Smart Array nnnn Controller y.yy In this case, press the Enter key and then go to step 7. 6. Review the information on the Caution screen, and then press the Enter key to reprogram the controller ROM. The following message is displayed: Reprogramming Firmware Do not interrupt the reprogramming process. You will be notified when reprogramming is complete. 7. When the reprogramming of the controller ROM is finished, you can reprogram more options or exit the utility. - To reprogram another Compaq option, press the Enter key, and then repeat steps 5 through 7. - If you have finished reprogramming Compaq options, press the Esc key to exit the utility. 8. Remove the Options ROMPaq diskette and restart the server. Updating the System Partition If you are installing the controller on a server that was previously configured with SCU, you must now use this utility to update the system partition. NOTE: If your server uses the ROM-Based Setup Utility (RBSU), you do not need to run SCU. Compaq Smart Array 5i Plus Controller and Battery Backed Write Cache Enabler User Guide 5-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
Updating the Controller Firmware
Compaq Smart Array 5i Plus Controller and Battery Backed Write Cache Enabler User Guide
5-5
—
If the screen message reads as follows, press the
Enter
key, and then go to
step 8 of these instructions:
The ROM image files found for the device selected are not
newer than the current ROM image
—
If the ROM firmware currently on the controller is older than that on the
Options ROMPaq diskette, then the screen message reads as follows:
Device to reprogram:
All Compaq Smart Array
nnnn
Controller(s)
Controller(s) Current ROM revision: Compaq Smart Array
nnnn
Controller
x.xx
Select Firmware Images: Compaq Smart Array
nnnn
Controller
y.yy
In this case, press the
Enter
key and then go to step 7.
6.
Review the information on the
Caution
screen, and then press the
Enter
key to
reprogram the controller ROM.
The following message is displayed:
Reprogramming Firmware
Do not interrupt the reprogramming process. You will be notified when
reprogramming is complete.
7.
When the reprogramming of the controller ROM is finished, you can reprogram
more options or exit the utility.
—
To reprogram another Compaq option, press the
Enter
key, and then repeat
steps 5 through 7.
—
If you have finished reprogramming Compaq options, press the
Esc
key to
exit the utility.
8.
Remove the Options ROMPaq diskette and restart the server.
Updating the System Partition
If you are installing the controller on a server that was previously configured with
SCU, you must now use this utility to update the system partition.
NOTE:
If your server uses the ROM-Based Setup Utility (RBSU), you do not need to run SCU.