HP 8/20q HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Event Message R - Page 24

specified Fibre Channel FC, but that device was

Get HP 8/20q PDF manuals and user guides View all HP 8/20q manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Table 4 Alarm events and recommended action (Continued) Icon Event ID and message Description Action (A1004.0048) (Eport Isolating due to Port Binding failure) A switch device attempted to login as an inter-switch link (ISL), but that device was not configured in the port binding list. Add the device to the port binding list. (A1004.0049) (Eport Isolating due to Remote inactive) The remote switch is unresponsive, and the link has not been brought up. The port will be isolated because the remote switch failed to respond. Investigate the remote switch for connection problems. (A1004.0050) (Maximum hard zoning member limit exceeded, Reverting to soft zoning. Requires port reset.) The maximum number of zone members associated with a port is limited to 64. If this number is exceeded, the switch cannot enforce hard zoning and will revert to soft zoning. Reduce the number of zone members associated with the port and reset the port. (A1004.0052) (Eport Isolating due to Switch Binding failure) A device attempted to login as an inter-switch link (ISL), but that device was not configured in the switch binding list. Add the device to the switch binding list. (A1004.0053) (Adding Denial of Service entry for source FC Address 0xaddress) A number of frames from the indicated address have been received. These frames are from a source that is not zoned with the destination. A denial of service entry will be set up to discard these frames. Investigate the source at the specified Fibre Channel (FC) address. (A1004.0054) (Eport Isolating due to Link to self) Two ports on the same switch Disconnect one or both ports. cannot be connected to one another. (A1004.0060) (Virtual Lanes configuration change will take effect on next port reset) The virtual lanes configuration does not become active until you reset the port. Reset the port. (A1005.0006) (Request from WWN device_WWN address FC_address, failed authentication, verify MS security configuration) Management server authentication is enabled, and the received frame failed authentication. Verify the MS group configuration. (A1005.000A) (Cannot enforce zoning for member domain_ID, port_number, this zone member will be ignored) A zone member given by domain ID and port number could not be found in the fabric. Examine the fabric connections and zoning definitions. 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
24
(A1004.0048) (Eport
Isolating due to Port
Binding failure)
A switch device attempted to
login as an inter-switch link
(ISL), but that device was not
configured in the port
binding list.
Add the device to the port
binding list.
(A1004.0049) (Eport
Isolating due to Remote
inactive)
The remote switch is
unresponsive, and the link
has not been brought up. The
port will be isolated because
the remote switch failed to
respond.
Investigate the remote switch
for connection problems.
(A1004.0050) (Maximum
hard zoning member
limit exceeded,
Reverting to soft
zoning. Requires port
reset.)
The maximum number of
zone members associated
with a port is limited to 64. If
this number is exceeded, the
switch cannot enforce hard
zoning and will revert to soft
zoning.
Reduce the number of zone
members associated with the
port and reset the port.
(A1004.0052) (Eport
Isolating due to Switch
Binding failure)
A device attempted to login
as an inter-switch link (ISL),
but that device was not
configured in the switch
binding list.
Add the device to the switch
binding list.
(A1004.0053) (Adding
Denial of Service entry
for source FC Address
0x
address
)
A number of frames from the
indicated address have been
received. These frames are
from a source that is not
zoned with the destination. A
denial of service entry will be
set up to discard these
frames.
Investigate the source at the
specified Fibre Channel (FC)
address.
(A1004.0054) (Eport
Isolating due to Link
to self)
Two ports on the same switch
cannot be connected to one
another.
Disconnect one or both ports.
(A1004.0060) (Virtual
Lanes configuration
change will take effect
on next port reset)
The virtual lanes
configuration does not
become active until you reset
the port.
Reset the port.
(A1005.0006) (Request
from WWN
device_WWN
address
FC_address
,
failed authentication,
verify MS security
configuration)
Management server
authentication is enabled,
and the received frame failed
authentication.
Verify the MS group
configuration.
(A1005.000A) (Cannot
enforce zoning for
member
domain_ID
,
port_number
, this zone
member will be ignored)
A zone member given by
domain ID and port number
could not be found in the
fabric.
Examine the fabric
connections and zoning
definitions.
Table 4
Alarm events and recommended action (Continued)
Icon
Event ID and message
Description
Action