HP 8/20q HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Event Message R - Page 27

and the Fibre Channel FC, the Network Time Protocol - fc 8 ports active switch

Get HP 8/20q PDF manuals and user guides View all HP 8/20q manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Table 4 Alarm events and recommended action (Continued) Icon Event ID and message Description Action (A1005.004F) (Media device sensor is value units. Transitioning from state to state) The specified sensor (Temperature, Voltage, TxBias, TxPower, or RxPower) has set a fault. The sensor reports its value (°Celsius, volts, milliAmps, milliWatts) and transition states (low alarm, low warning, normal, high warning, high alarm). For the temperature sensor transitioning from low alarm to high alarm, cool the system. For all other sensors transitioning from low alarm to high alarm, replace the media. (A1005.0050) (Media device device_name is value units. Transitioning from state to state) The specified sensor (Temperature, Voltage, TxBias, TxPower, or RxPower) has cleared an existing fault. The sensor reports its value (°Celsius, volts, milliAmps, milliWatts) and transition states (low alarm, low warning, normal, high warning, high alarm). None (A1005.006A) (User account account_name has expired) The named user account has Review the user account and exceeded its expiration date. make the necessary corrections. (A1005.006B)(Temperatur e too high, turning off lasers) The switch has overheated and the Fibre Channel (FC) port lasers have been turned off. Power down the switch, correct the conditions that caused the switch to overheat, and then power up the switch. (A1005.006C) (3.3V out of spec, turning off lasers) Switch ports are receiving incorrect voltages. Lasers have been turned off. Contact your authorized maintenance provider. (A1005.006D) (Unable to synchronize with NTP server) The switch was unable to synchronize its time clock with the Network Time Protocol (NTP) server. Confirm that the NTP service and NTP client are enabled. Confirm that the NTP server IP address is correct and that the server is operating. (A1005.006E) (A reset is required to activate this version of firmware) The installed firmware cannot Perform a hard reset. be activated without disrupting I/O traffic. (A1005.006F) (Hotreset Vversion -> Vversion is not supported) The installed firmware cannot Perform a hard reset. be activated without disrupting I/O traffic. HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Event Message Reference Guide 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Event Message Reference Guide
27
(A1005.004F) (Media
device
sensor
is
value
units
. Transitioning
from
state
to
state
)
The specified sensor
(
Temperature
,
Voltage
,
TxBias
,
TxPower
, or
RxPower
) has set a fault. The
sensor reports its value
(
°Celsius
,
volts
,
milliAmps
,
milliWatts
)
and transition states
(
low alarm
,
low warning
,
normal
,
high warning
,
high alarm
).
For the temperature sensor
transitioning from
low
alarm
to
high alarm
, cool
the system. For all other
sensors transitioning from
low alarm
to
high alarm
, replace the
media.
(A1005.0050) (Media
device
device_name
is
value units
.
Transitioning from
state
to
state
)
The specified sensor
(
Temperature
,
Voltage
,
TxBias
,
TxPower
, or
RxPower
) has cleared an
existing fault. The sensor
reports its value (
°Celsius
,
volts
,
milliAmps
,
milliWatts
) and transition
states (
low alarm
,
low warning
,
normal
,
high warning
,
high alarm
).
None
(A1005.006A) (User
account
account_name
has expired)
The named user account has
exceeded its expiration date.
Review the user account and
make the necessary
corrections.
(A1005.006B)(Temperatur
e too high, turning off
lasers)
The switch has overheated
and the Fibre Channel (FC)
port lasers have been turned
off.
Power down the switch,
correct the conditions that
caused the switch to
overheat, and then power up
the switch.
(A1005.006C) (3.3V out
of spec, turning off
lasers)
Switch ports are receiving
incorrect voltages. Lasers
have been turned off.
Contact your authorized
maintenance provider.
(A1005.006D) (Unable to
synchronize with NTP
server)
The switch was unable to
synchronize its time clock with
the Network Time Protocol
(NTP) server.
Confirm that the NTP service
and NTP client are enabled.
Confirm that the NTP server
IP address is correct and that
the server is operating.
(A1005.006E) (A reset
is required to activate
this version of
firmware)
The installed firmware cannot
be activated without
disrupting I/O traffic.
Perform a hard reset.
(A1005.006F) (Hotreset
V
version
-> V
version
is
not supported)
The installed firmware cannot
be activated without
disrupting I/O traffic.
Perform a hard reset.
Table 4
Alarm events and recommended action (Continued)
Icon
Event ID and message
Description
Action