HP 8/20q HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Event Message R - Page 31

Data EFMD frame. The port, Security Attributes ESA

Get HP 8/20q PDF manuals and user guides View all HP 8/20q manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Table 4 Alarm events and recommended action (Continued) Icon Event ID and message Description Action (A1007.0007) (Security: Fabric Binding (ESA) not supported on remote switch and Fabric Binding is enabled, failing security checks) Either fabric binding is not enabled on the remote switch or the remote switch does not support security at all. Check the security configuration on the remote switch. (A1007.0008) (Security: ESA Response failure, failing security checks) A failure was received during processing of the Exchange Security Attributes (ESA) received frame. Either the payload did not match the standard layout or the payload status indicated a reject. Check for errors on the remote side of the link. Check the transceiver and cable. Update firmware on the remote switch. (A1007.0009) (Security checks EFMD response failure, failing security check.) A remote switch rejected an Exchange Fabric Membership Data (EFMD) frame. The port will be isolated. Check the remote switch for the reason that the EFMD frame was rejected. It is possible that the FabricBindingEnabled parameter is different on the two switches. (A1007.000A) (Security: Dropping lock held by domain domain_id for number seconds) A remote switch has held the fabric lock for too long. The local switch is dropping the lock in order to send out an Exchange Fabric Membership Data (EFMD) frame. None (A1007.000B) (Security: EFMD Rejected, bad revision) The remote switch is running at a different Exchange Fabric Membership Data (EFMD) version level than the local switch. Ports will isolate. None (A1007.000C) (Security policy restrict mode, security db differs) The current security policy calls for Restrict mode, which means that all switches in the fabric must have the same security databases or the Fabric inter-switch links (ISL)s will not log in. In this case, the security databases differ. Reconfigure the active security set so that the ISL group members are the same. (A1007.000D) (Security policy in mode mode, other switch in mode mode, sec db conflict) The security policy on the local switch differs from that of the remote switch. Configure the security policy on the remote switch to match that of the local switch. (A1007.000E) (Security: Auth challenge received from WWN port_WWN, not Authorized to join) A challenge authentication frame was received from a remote switch, but the local switch does not have an entry for itself within the active security set ISL group. Edit the ISL group to include the local switch. HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Event Message Reference Guide 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
HP StorageWorks 8/20q and SN6000 Fibre Channel Switch Event Message Reference Guide
31
(A1007.0007) (Security:
Fabric Binding (ESA)
not supported on remote
switch and Fabric
Binding is enabled,
failing security
checks)
Either fabric binding is not
enabled on the remote switch
or the remote switch does not
support security at all.
Check the security
configuration on the remote
switch.
(A1007.0008) (Security:
ESA Response failure,
failing security
checks)
A failure was received during
processing of the Exchange
Security Attributes (ESA)
received frame. Either the
payload did not match the
standard layout or the
payload status indicated a
reject.
Check for errors on the
remote side of the link. Check
the transceiver and cable.
Update firmware on the
remote switch.
(A1007.0009) (Security
checks EFMD response
failure, failing
security check.)
A remote switch rejected an
Exchange Fabric Membership
Data (EFMD) frame. The port
will be isolated.
Check the remote switch for
the reason that the EFMD
frame was rejected. It is
possible that the
FabricBindingEnabled
parameter is different on the
two switches.
(A1007.000A) (Security:
Dropping lock held by
domain
domain_id
for
number
seconds)
A remote switch has held the
fabric lock for too long. The
local switch is dropping the
lock in order to send out an
Exchange Fabric Membership
Data (EFMD) frame.
None
(A1007.000B) (Security:
EFMD Rejected, bad
revision)
The remote switch is running
at a different Exchange
Fabric Membership Data
(EFMD) version level than the
local switch. Ports will isolate.
None
(A1007.000C) (Security
policy restrict mode,
security db differs)
The current security policy
calls for Restrict mode, which
means that all switches in the
fabric must have the same
security databases or the
Fabric inter-switch links (ISL)s
will not log in. In this case,
the security databases differ.
Reconfigure the active
security set so that the ISL
group members are the same.
(A1007.000D) (Security
policy in
mode
mode,
other switch in
mode
mode, sec db conflict)
The security policy on the
local switch differs from that
of the remote switch.
Configure the security policy
on the remote switch to match
that of the local switch.
(A1007.000E) (Security:
Auth challenge received
from WWN
port_WWN
, not
Authorized to join)
A challenge authentication
frame was received from a
remote switch, but the local
switch does not have an entry
for itself within the active
security set ISL group.
Edit the ISL group to include
the local switch.
Table 4
Alarm events and recommended action (Continued)
Icon
Event ID and message
Description
Action