Home » HP Manuals » Print Servers » HP J7934A » Manual Viewer

HP J7934A HP Jetdirect Administrator's Guide - Page 226

Table 9.11, Error Messages 2 of 11, HP Jetdirect Configuration

UPC - 829160279466

Add to My Manuals
Save this manual to your list of manuals

Page 226 highlights

Table 9.11 Error Messages (2 of 11) Error Code and Message 09 SCANNING FOR SSID 0A LAN ERROR NO SQE 0C LAN ERROR RECEIVER OFF 0D LAN ERROR TRANSMITTER OFF 0E LAN ERROR LOSS OF CARRIER 10 LAN ERROR UNDERFLOW 11 LAN ERROR RETRY FAULTS 12 LAN ERROR NO LINKBEAT 13 NETWORK RECONFIG - MUST REBOOT Description (802.11 Wireless) The print server is scanning on all channels for devices on the specified SSID (network name). Check your specified SSID, or check status of the Access Point (Infrastructure mode) or other wireless devices. The print server will continue to scan for the specified SSID. (Wired Ethernet) Check the network connections. If the connections are intact, run the power-on self-test: turn the printer off, then on again. If the error persists, replace the HP Jetdirect print server. There may be a problem with your network cabling or the HP Jetdirect print server. Check the cabling and connectors on your Ethernet network. If you cannot find a problem with your network cabling, run the power-on self-test: turn the printer off, then on again. If the error persists after the printer is turned on again, there is a problem with the HP Jetdirect print server. There may be a problem with your network cabling or the HP Jetdirect print server. Check the cabling and connectors on your Ethernet network. If you cannot find a problem with your network cabling, run the power-on self-test: turn the printer off, then on again. If the error persists, there is a problem with the HP Jetdirect print server. Check the network connections. If the connections are intact, run the power-on self-test: turn the printer off, then on again. If the error persists, replace the HP Jetdirect print server. (Wired Ethernet) There may be a problem with your network cabling or the HP Jetdirect print server. Check the cabling and connectors on your network. If you cannot find a problem with your network cabling, run the power-on self-test: turn the printer off, then on again. If the error persists, there is a problem with the HP Jetdirect print server. (Wired Ethernet) There is a problem with your network cabling or external network configuration. Verify operation of the hub or switch port. With a 10/100 Base-TX port connected, this message is displayed if Link Beat is not sensed. Check the network cable, and verify that the concentrator/hub is providing Link Beat. Reset or power off/on the HP Jetdirect print server to enable new configuration values. ENWW HP Jetdirect Configuration Page 226

Section	Page
Introducing the HP Jetdirect PrintServer	7
Introduction	7
Supported Print Servers	8
Supported Network Protocols	8
Security Protocols	10
SNMP (IP and IPX)	10
HTTPS	10
Authentication	10
Supplied Manuals	12
HP Support	12
HP Online Support	12
Firmware Upgrades	12
HP Support By Phone	14
Product Registration	14
Product Accessibility	14
HP Software Solutions Summary	15
Introduction	15
HP Install Network Printer Wizard (Windows)	18
Requirements	18
HP Jetdirect Printer Installer for UNIX	19
HP Web Jetadmin	20
System Requirements	20
Installing HP Web Jetadmin	21
Configuring and Modifying a Device	22
Removing HPWeb Jetadmin Software	22
Internet Printer Connection Software	23
HP-Supplied Software	23
Microsoft Supplied Software	24
Novell Supplied Software	25
HP IP/IPX Printer Gateway for NDPS	26
Features	26
To Get the Software	27
HP WPS Assistant (Mac OS X)	27
HP LaserJet Utilities for Mac OS	28
Installing the Printer Software	28
Configuring the Printer	29
Verifying Network Configuration	30
Renaming the Printer	30
Selecting a Zone	31
Selecting Your Printer	32
Testing the Configuration	33
TCP/IP Configuration	34
Introduction	34
Server-Based and Manual TCP/IP Configuration	34
Default IP Address	35
Default IP Address Will Not Be Assigned	35
Default IP Address Will Be Assigned	35
Default IP Address Configuration Options	36
Default IP on Wireless and Wired Print Servers	37
TCP/IP Configuration Tools	38
Using BOOTP/TFTP	40
Why Use BOOTP/TFTP?	41
BOOTP/TFTP on UNIX	41
Using DHCP	62
UNIX Systems	63
Windows Systems	63
NetWare Systems	68
To Discontinue DHCP Configuration	68
Using RARP	70
Using the arp and ping Commands	72
Using Telnet	74
Creating a Telnet Connection	74
A Typical Telnet Session	76
User Interface Options	77
Using Telnet to Erase the Existing IP Settings	98
Using the Embedded Web Server	98
Using the Printer Control Panel	99
Moving to Another Network	100
Using the Embedded Web Server	101
Introduction	101
Requirements	103
Compatible Web Browsers	103
Supported HPWeb Jetadmin Version	103
Viewing the Embedded Web Server	104
Operating Notes	106
HPJetdirect Home Tab	107
Networking Tab	109
Sending Product Information to HP	109
Network Settings	110
Other Settings	122
Privacy Settings	134
Select Language	134
Settings	134
Authorization	138
Mgmt. Protocols	146
802.1x Authentication	150
Wireless	152
Network Statistics	152
Protocol Info	152
Configuration Page	152
Other Links	153
Help	153
Support	153
HPHome	153
HPWeb Jetadmin	153
Configuring for LPD Printing	154
Introduction	154
About LPD	155
Requirements for Configuring LPD	156
LPD Setup Overview	156
Step 1. Setting Up IP Parameters	156
Step 2. Setting Up Print Queues	157
Step 3. Printing a Test File	157
LPD on UNIX Systems	158
Printing a Test File	161
LPD on Windows NT/2000/Server 2003 Systems	162
Installing TCP/IP Software	162
Configuring a Network Printer for Windows2000/Server 2003 Systems	164
Configuring a Network Printer for WindowsNT4.0 Systems	166
Printing from Windows Clients	167
LPD on Windows XP Systems	167
Adding Windows Optional Networking Components	167
Configuring a Network LPD Printer	168
LPD on Mac OS Systems	169
Assigning an IP Address	170
Setting Up Mac OS	170
FTP Printing	172
Introduction	172
Requirements	172
Print Files	173
Using FTP Printing	173
FTP Connections	173
FTP Login	175
Ending the FTP Session	176
Commands	176
Example of an FTP Session	178
Security Features	179
Introduction	179
Using Security Features	183
Troubleshooting the HPJetdirect PrintServer	185
Introduction	185
Resetting to Factory Defaults	186
General Troubleshooting	188
Troubleshooting Chart - Assessing the Problem	188
Procedure 1: Verifying that the Printer is On and Online	189
Procedure 2: Printing an HPJetdirect Configuration Page	190
Procedure 3: Resolving Printer Display ErrorMessages	191
Procedure 4: Resolving Printer Communication Problems with the Network	193
Troubleshooting Wireless Print Servers	196
Unable to Communicate During Initial Setup	196
Unable to Communicate After Initial Setup	197
My Configured Channel Does Not Match the Configuration Page	197
Unable to Use the HP Jetdirect Install Network Printer Wizard	198
Improving Reception and Performance	198
Firmware Download Failure	199
Troubleshooting an LPD UNIX Configuration	200
HPJetdirect Configuration Page	202
Introduction	202
Status Field Error Messages	202
Configuration Page Format	203
Configuration Page Messages	205
HPJetdirect Configuration/General Information	205
USB Printer Settings	207
802.11 Wireless Settings	208
Security Settings	211
Network Statistics	214
TCP/IP Protocol Information	215
IPX/SPX Protocol Information	219
Novell NetWare Parameters	221
AppleTalk Protocol Information	223
DLC/LLC Protocol Information	224
Error Messages	225
TCP/IP Overview	236
Introduction	236
Internet Protocol (IP)	236
Transmission Control Protocol (TCP)	237
User Datagram Protocol (UDP)	237
IP Address	237
IP Address: (Network Portion)	238
IP Address: (Host Portion)	238
IP Address Structure and Class	239
Configuring IP Parameters	240
Dynamic Host Configuration Protocol (DHCP)	240
BOOTP	240
Subnets	241
Subnet Mask	241
Gateways	242
Default Gateway	242
Syslog Server	242
The HPJetdirect EIO Control PanelMenu	245
Introduction	245
Classic Control Panel	246
Graphical Control Panel	249
OpenSSL Statements	253

Match case Limit results 1 per page

ENWW

HP Jetdirect Configuration Page 226

09 SCANNING FOR

SSID

(802.11 Wireless) The print server is scanning on all

channels for devices on the specified SSID (network name).

Check your specified SSID, or check status of the Access

Point (Infrastructure mode) or other wireless devices.

The print server will continue to scan for the specified SSID.

0A LAN ERROR -

NO SQE

(Wired Ethernet) Check the network connections. If the

connections are intact, run the power-on self-test: turn the

printer off, then on again. If the error persists, replace the

HP Jetdirect print server.

0C LAN ERROR -

RECEIVER OFF

There may be a problem with your network cabling or the

Jetdirect print server. Check the cabling and connectors

on your Ethernet network. If you cannot find a problem with

your network cabling, run the power-on self-test: turn the

printer off, then on again. If the error persists after the printer

is turned on again, there is a problem with the HP Jetdirect

print server.

0D LAN ERROR -

TRANSMITTER OFF

There may be a problem with your network cabling or the

Jetdirect print server. Check the cabling and connectors

on your Ethernet network. If you cannot find a problem with

your network cabling, run the power-on self-test: turn the

printer off, then on again. If the error persists, there is a

problem with the HP Jetdirect print server.

0E LAN ERROR -

LOSS OF CARRIER

Check the network connections. If the connections are

intact, run the power-on self-test: turn the printer off, then

on again. If the error persists, replace the HP Jetdirect

print server.

10 LAN ERROR -

UNDERFLOW

(Wired Ethernet) There may be a problem with your network

cabling or the HP Jetdirect print server. Check the cabling

and connectors on your network. If you cannot find a

problem with your network cabling, run the power-on

self-test: turn the printer off, then on again. If the error

persists, there is a problem with the HP Jetdirect print

server.

11 LAN ERROR -

RETRY FAULTS

(Wired Ethernet) There is a problem with your network

cabling or external network configuration. Verify operation

of the hub or switch port.

12 LAN ERROR -

NO LINKBEAT

With a 10/100 Base-TX port connected, this message is

displayed if Link Beat is not sensed. Check the network

cable, and verify that the concentrator/hub is providing Link

Beat.

13 NETWORK

RECONFIG - MUST

REBOOT

Reset or power off/on the HP

Jetdirect print server to enable

new configuration values.

Table 9.11

Error Messages (2 of 11)

Error Code and

Message

Description