HP J7934A HP Jetdirect Administrator's Guide - Page 82

Table 3.4, Telnet Commands and Parameters 4 of 18, TCP/IP Configuration 82

Page 82 highlights

Table 3.4 Telnet Commands and Parameters (4 of 18) wpa-auth-type This command is not compatible with the Shared Key authentication option in the auth-type command. Use this command to specify WPA-PSK authentication. PSK: WPA-PSK provides enhanced authentication where an authentication server is not used. Instead, a Pre-shared key provides device authentication. A Pre-shared key is generated when you specify a network pass-phrase using the psk-passphrase command. The dynamic-encrypt command should be set to the Robust option. psk-passphrase Specify a pass-phrase that is used to generate a network Pre-shared key. A pass-phrase must be from 8 to 63 ASCII characters in the hexadecimal range 21 through 7E (characters 0-9, a-z, A-Z and numerous special characters including dynamic-encrypt For WPA-PSK authentication, use this command to set the print server for dynamic Wi-Fi Protected Access (WPA) encryption. Specify Robust as the command option. 802.11 Wireless Diagnostics Command Description Current SSID (Read-only parameter) The network name (SSID) to which the wireless print server connected. Current Channel (Read-only parameter) The channel that the wireless print server is currently using. Signal Strength (Read-only parameter) The strength of the radio signal received by the print server. : No radio signal detected while the print server is scanning. No Signal: No radio signal detected on any channel. Poor/Marginal/Good/Excellent: Indicates the detected signal strength level. Access Point Mac (Read-only parameter) The Media Access Control (MAC) address of the Access Point used for Infrastructure mode communications. For example, 00:a0:f8:38:7a:f7 specifies that the Access Point with MAC address 00a0f8387af7 was used for communicating on the network. ENWW TCP/IP Configuration 82

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264

ENWW
TCP/IP Configuration 82
wpa-auth-type
This command is not compatible with the Shared Key
authentication option in the
auth-type
command. Use this
command to specify WPA-PSK authentication.
PSK
: WPA-PSK provides enhanced authentication where
an authentication server is not used. Instead, a Pre-shared
key provides device authentication. A Pre-shared key is
generated when you specify a network pass-phrase using
the
psk-passphrase
command. The
dynamic-encrypt
command should be set to the
Robust
option.
psk-passphrase
Specify a pass-phrase that is used to generate a network
Pre-shared key. A pass-phrase must be from 8 to 63 ASCII
characters in the hexadecimal range 21 through 7E
(characters 0-9, a-z, A-Z and numerous special characters
including !, @, #, $, %, ^, &, (, ), _, +, =, -, {, }, [, ], \, /, “, <,
>, ?, “, ‘, ~).
dynamic-encrypt
For WPA-PSK authentication, use this command to set the
print server for dynamic Wi-Fi Protected Access (WPA)
encryption. Specify
Robust
as the command option.
802.11 Wireless Diagnostics
Command
Description
Current SSID
(Read-only parameter) The network name (SSID) to which
the wireless print server connected.
Current Channel
(Read-only parameter) The channel that the wireless print
server is currently using.
Signal Strength
(Read-only parameter) The strength of the radio signal
received by the print server.
<blank>
: No radio signal detected while the print server is
scanning.
No Signal
: No radio signal detected on any channel.
Poor/Marginal/Good/Excellent
: Indicates the detected
signal strength level.
Access Point Mac
(Read-only parameter) The Media Access Control (MAC)
address of the Access Point used for Infrastructure mode
communications. For example,
00:a0:f8:38:7a:f7
specifies that the Access Point with MAC address
00a0f8387af7 was used for communicating on the network.
Table 3.4
Telnet Commands and Parameters (4 of 18)