HP ProLiant 4500 Compaq ProLiant 4500R Rack-Mountable Servers Maintenance and - Page 17

Hot-Pluggable Hard Drives

Get HP ProLiant 4500 PDF manuals and user guides View all HP ProLiant 4500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Removal and Replacement Procedures 2-5 3. Slide base frame back to access cables in drive cage. 4. Lift protective cover and disconnect power and signal cables to device. 5. Remove media trim piece retaining screws (2) from front bezel. 6. Remove the storage device retaining screws (2) and slide out. 7. Reverse steps for installation. The following table shows the supported mass storage devices and their supported locations. Table 2-1 Removable Media Bay Configurations Mass Storage Device 1.44-MB, 3.5" Diskette Drive 1.2-MB, 5.25" Diskette Drive 2/8-GB DAT (Digital Audio Tape) Drive 525-MB ACA Tape Drive CD-ROM Drive 4/16-GB TurboDAT Drive 1.2-GB Tape Drive TurboDAT Drive w/ Autoloader (Requires bays 5 and 6) Storage Bays 7 6 5 ü ü ü ü ü ü ü ü ü ü ü ü ü ü Hot-Pluggable Hard Drives Hot-Pluggable hard drives used in combination with the Compaq Smart SCSI Array Controller can be replaced while the power is still on. NOTE: It is not necessary to set the SCSI ID jumpers on a Compaq replacement HotPluggable hard drive. The SCSI ID is set automatically by the backplane board and the Hot-Pluggable tray when the drive is installed. CAUTION: Before removing any Hot-Pluggable hard drive, read the guidelines listed in the following section. Maintenance and Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
Removal and Replacement Procedures
2-5
Maintenance and Service Guide
3.
Slide base frame back to access cables in drive cage.
4.
Lift protective cover and disconnect power and signal cables to device.
5.
Remove media trim piece retaining screws (2) from front bezel.
6.
Remove the storage device retaining screws (2) and slide out.
7.
Reverse steps for installation.
The following table shows the supported mass storage devices and their supported locations.
Table 2-1
Removable Media Bay Configurations
Storage Bays
Mass Storage Device
7
6
5
1.44-MB, 3.5" Diskette Drive
ü
ü
1.2-MB, 5.25" Diskette Drive
ü
2/8-GB DAT (Digital Audio Tape) Drive
ü
ü
525-MB ACA Tape Drive
ü
ü
CD-ROM Drive
ü
4/16-GB TurboDAT Drive
ü
ü
1.2-GB Tape Drive
ü
ü
TurboDAT Drive w/ Autoloader (Requires bays 5 and 6)
ü
ü
Hot-Pluggable Hard Drives
Hot-Pluggable hard drives used in combination with the Compaq Smart SCSI Array Controller
can be replaced while the power is still on.
NOTE:
It is not necessary to set the SCSI ID jumpers on a Compaq replacement Hot-
Pluggable hard drive.
The SCSI ID is set automatically by the backplane board and the
Hot-Pluggable tray when the drive is installed.
CAUTION:
Before removing any Hot-Pluggable hard drive, read the guidelines listed in
the following section.