HP ProLiant 4500 Compaq ProLiant 4500R Rack-Mountable Servers Maintenance and - Page 23

Memory

Get HP ProLiant 4500 PDF manuals and user guides View all HP ProLiant 4500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Removal and Replacement Procedures 2-11 Memory The ProLiant 4500R Server comes standard with 16 megabytes of system memory. Memory can be expanded to a maximum of 1.024 gigabytes by installing a matched set of four 4-, 8-, 16-, 32-, or 64-megabyte 60-, 70-, or 80-ns JEDEC standard SIMM modules in the eight SIMM sockets on the system board for a total of 512 megabytes and the eight SIMM sockets on the 512-megabyte Memory Expansion Board. Figure 2-10. Removing the SIMM Module 1. Extend the server from the rack. 2. Remove the cover plate. 3. Remove the Y brace and card bracket. 4. Press the SIMM connector latches outward [A]. 5. Tilt the SIMM module forward [B]. 6. Lift the SIMM module out [C]. 7. To replace the SIMM module, reverse these steps. IMPORTANT: Run Compaq System Configuration Utility if installed memory size has changed. A POST error message will be displayed at power up prompting you to run the System Configuration Utility. The following guidelines MUST be followed when installing or replacing memory: n SIMMs must be installed in matched sets of four at time; for example: four 16-megabyte modules. n Matched SIMMs must be the same size and speed. n Install SIMM sets in bank 1 first, then in bank 2. CAUTION: Use only JEDEC standard SIMMs. Non-JEDEC SIMMs may adversely affect data integrity. Maintenance and Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
Removal and Replacement Procedures
2-11
Maintenance and Service Guide
Memory
The ProLiant 4500R Server comes standard with 16 megabytes of system memory.
Memory can
be expanded to a maximum of 1.024 gigabytes by installing a matched set of four 4-, 8-, 16-, 32-,
or 64-megabyte 60-, 70-, or 80-ns JEDEC standard SIMM modules in the eight SIMM sockets on
the system board for a total of 512 megabytes and the eight SIMM sockets on the 512-megabyte
Memory Expansion Board.
Figure 2-10.
Removing the SIMM Module
1.
Extend the server from the rack.
2.
Remove the cover plate.
3.
Remove the Y brace and card bracket.
4.
Press the SIMM connector latches outward [A].
5.
Tilt the SIMM module forward [B].
6.
Lift the
SIMM module out [C].
7.
To replace the SIMM module, reverse these steps.
IMPORTANT:
Run Compaq System Configuration Utility if installed memory
size has changed.
A POST error message will be displayed at power up
prompting you to run the System Configuration Utility.
The following guidelines
MUST
be followed when installing or replacing memory:
n
SIMMs must be installed in matched sets of four at time; for example: four 16-megabyte
modules.
n
Matched SIMMs must be the same size and speed.
n
Install SIMM sets in bank 1 first, then in bank 2.
CAUTION:
Use only JEDEC standard SIMMs. Non-JEDEC SIMMs may
adversely affect data integrity.