HP ProLiant 4500 Compaq ProLiant 4500R Rack-Mountable Servers Maintenance and - Page 63

FYI: Drive bay

Get HP ProLiant 4500 PDF manuals and user guides View all HP ProLiant 4500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

Diagnostic Tools 3-31 Error occurred reading RIS copy from drive (bay) X An error occurred while DAAD was trying to read the RIS from this drive. If there were multiple errors, this drive may need to be replaced. FYI: Drive (bay) X is non-Compaq supplied The installed drive was not supplied by Compaq. If problems exist with this drive, replace it with a Compaq drive. Identify controller data did not match with CMOS The identify controller data from the array controller did not match with the information stored in nonvolatile RAM. This could occur if new, previously configured drives have been placed in a system that has also been previously configured. It could also occur if the firmware on the controller has been upgraded and the System Configuration Utility was not run. Check the identify controller data under the Inspect Utility. If the firmware version field is the only thing different between the controller and nonvolatile RAM data, this is not a problem. Otherwise run the System Configuration Utility. Identify logical drive data did not match with CMOS The identify unit data from the array controller did not match with the information stored in nonvolatile RAM. This could occur if new, previously configured drives have been placed in a system that has also been previously configured. Run the System Configuration Utility to configure the controller and nonvolatile RAM. Insufficient adapter resources The adapter does not have sufficient resources to perform operations to the array accelerator board. Drive rebuild may be occurring. Operate the system without the array accelerator board until the drive rebuild completes. Less than 75% batteries at sufficient voltage The operation of the array accelerator board has been disabled due to less than 75% of the battery packs being at the sufficient voltage level. Allow sufficient time for the batteries to recharge (36 hours). If the batteries have not recharged after 36 hours, replace the array accelerator board. Logical drive X failed due to cache error This logical drive failed due to a catastrophic cache error. Replace the array accelerator board and re-configure using the System Configuration Utility. Maintenance and Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
Diagnostic Tools
3-31
Maintenance and Service Guide
Error occurred reading RIS copy from drive (bay)
X
An error occurred while DAAD was trying to read the RIS from this drive.
If there were multiple errors, this drive may need to be replaced.
FYI: Drive (bay)
X
is non-Compaq supplied
The installed drive was not supplied by Compaq.
If problems exist with this drive, replace it with a Compaq drive.
Identify controller data did not match with CMOS
The identify controller data from the array controller did not match with the information
stored in nonvolatile RAM. This could occur if new, previously configured drives have been
placed in a system that has also been previously configured. It could also occur if the
firmware on the controller has been upgraded and the System Configuration Utility was not
run.
Check the identify controller data under the Inspect Utility. If the firmware version field is
the only thing different between the controller and nonvolatile RAM data, this is not a
problem. Otherwise run the System Configuration Utility.
Identify logical drive data did not match with CMOS
The identify unit data from the array controller did not match with the information stored in
nonvolatile RAM. This could occur if new, previously configured drives have been placed in
a system that has also been previously configured.
Run the System Configuration Utility to configure the controller and nonvolatile RAM.
Insufficient adapter resources
The adapter does not have sufficient resources to perform operations to the array accelerator
board. Drive rebuild may be occurring.
Operate the system without the array accelerator board until the drive rebuild completes.
Less than 75% batteries at sufficient voltage
The operation of the array accelerator board has been disabled due to less than 75% of the
battery packs being at the sufficient voltage level.
Allow sufficient time for the batteries to recharge (36 hours). If the batteries have not
recharged after 36 hours, replace the array accelerator board.
Logical drive
X
failed due to cache error
This logical drive failed due to a catastrophic cache error.
Replace the array accelerator board and re-configure using the System Configuration Utility.