HP ProLiant 4500 Compaq ProLiant 4500R Rack-Mountable Servers Maintenance and - Page 65

No configuration for Accelerator Board

Get HP ProLiant 4500 PDF manuals and user guides View all HP ProLiant 4500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

Diagnostic Tools 3-33 Logical Drive X status = WRONG DRIVE REPLACED A physical drive in this logical drive has failed. The incorrect drive was replaced. Replace the drive that was incorrectly replaced. Then, replace the original drive that failed with a new drive. Do not run the System Configuration Utility to re-configure - you will lose data on the drive. Mirror data miscompare Data was found at re-initialization in the posted write memory, however, the mirror data compare test failed resulting in data being marked as invalid. Data loss is possible. Replace the array accelerator board. Mirrored memory location errors Soft errors occurred when attempting to read the same data from both sides of the mirrored memory. Data loss will occur. Replace the array accelerator board. No configuration for Accelerator Board The array accelerator board has not been configured. If the array accelerator board is present, run the System Configuration Utility to configure the board. Physical Drive (bay) X error occurred This message displays detailed information on any drive errors that were returned to DAAD while issuing drive commands. Check for other error conditions. Physical drive (bay) X has loose cable The array controller could not communicate with this drive at power-up. This drive has not previously failed. Check all cable connections first. The cables could be bad, loose, or disconnected. Turn on the system and attempt to reconnect data/power cable to the drive. If this does not work, replace the cable. If that does not work, the drive may need to be replaced. Physical drive (bay) X is a replacement drive This drive has been replaced. This message displays if a drive is replaced in a fault tolerant logical volume. If the replacement was intentional, allow the drive to rebuild. Physical drive (bay) X is a replacement drive marked OK This drive has been replaced and marked OK by the firmware. This may occur if a drive has an intermittent failure (for example, if a drive has previously failed, then when DAAD is run, the drive starts working again). Replace the drive. Maintenance and Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
Diagnostic Tools
3-33
Maintenance and Service Guide
Logical Drive
X
status = WRONG DRIVE
REPLACED
A physical drive in this logical drive has failed. The incorrect drive was replaced.
Replace the drive that was incorrectly replaced. Then, replace the original drive that failed
with a new drive.
Do not
run the System Configuration Utility to re-configure - you will lose
data on the drive.
Mirror data miscompare
Data was found at re-initialization in the posted write memory, however, the mirror data
compare test failed resulting in data being marked as invalid. Data loss is possible.
Replace the array accelerator board.
Mirrored memory location errors
Soft errors occurred when attempting to read the same data from both sides of the mirrored
memory. Data loss will occur.
Replace the array accelerator board.
No configuration for Accelerator Board
The array accelerator board has not been configured.
If the array accelerator board is present, run the System Configuration Utility to configure
the board.
Physical Drive (bay)
X
error occurred
This message displays detailed information on any drive errors that were returned to DAAD
while issuing drive commands.
Check for other error conditions.
Physical drive (bay)
X
has loose cable
The array controller could not communicate with this drive at power-up. This drive has not
previously failed.
Check all cable connections first. The cables could be bad, loose, or disconnected. Turn on
the system and attempt to reconnect data/power cable to the drive. If this does not work,
replace the cable. If that does not work, the drive may need to be replaced.
Physical drive (bay)
X
is a replacement drive
This drive has been replaced. This message displays if a drive is replaced in a fault tolerant
logical volume.
If the replacement was intentional, allow the drive to rebuild.
Physical drive (bay)
X
is a replacement drive
marked OK
This drive has been replaced and marked OK by the firmware. This may occur if a drive has
an intermittent failure (for example, if a drive has previously failed, then when DAAD is run,
the drive starts working again).
Replace the drive.