HP ProLiant 4500 Compaq ProLiant 4500R Rack-Mountable Servers Maintenance and - Page 59

Accelerator status: Valid data found at reset

Get HP ProLiant 4500 PDF manuals and user guides View all HP ProLiant 4500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Diagnostic Tools 3-27 Accelerator parity write errors: n This message displays the number of times that write memory parity errors were detected during transfers between the IDA-2 board transfer buffer and memory on the array accelerator board. If there are a number of these parity errors, you may need to replace the array accelerator board. Accelerator status: Permanently disabled The array accelerator board has been permanently disabled. It will remain disabled until it is reinitialized using the System Configuration Utility. Check the Disable Code field. Run the System Configuration Utility to reinitialize the array accelerator board. Accelerator status: Possible data loss in cache Possible data loss was detected during power-up due to all of the batteries being below the sufficient voltage level and no presence of the identification signatures on the array accelerator board. There is no way to determine if dirty or bad data was in the cache and is now lost. Accelerator status: Temporarily disabled The array accelerator board has been temporarily disabled. Check the Disable Code field. Accelerator status: Unrecognized status A status returned from the array accelerator board that DAAD does not recognize. Call your Authorized Compaq Reseller for the latest copy of DAAD. Accelerator status: Valid data found at reset Valid data was found in the posted write memory at re-initialization. The data will be flushed to disk. This is not an error or data loss condition. No action needs to be taken. Accelerator status: Warranty alert A catastrophic problem has occurred with the array accelerator board. Refer to the other messages on the Diagnostics screen for the exact meaning of this message. Replace the array accelerator board. Battery pack X below reference voltage The indicated battery pack is below the required voltage levels. Allow sufficient time for the batteries to recharge (36 hours). If the batteries have not recharged after 36 hours, replace the battery pack. Maintenance and Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
Diagnostic Tools
3-27
Maintenance and Service Guide
Accelerator parity write errors:
n
This message displays the number of times that write memory parity errors were detected
during transfers between the IDA-2 board transfer buffer and memory on the array
accelerator board.
If there are a number of these parity errors, you may need to replace the array
accelerator board.
Accelerator status: Permanently disabled
The array accelerator board has been permanently disabled. It will remain disabled until it is
reinitialized using the System Configuration Utility.
Check the Disable Code field. Run the System Configuration Utility to reinitialize the array
accelerator board.
Accelerator status: Possible data loss in cache
Possible data loss was detected during power-up due to all of the batteries being below the
sufficient voltage level and no presence of the identification signatures on the array
accelerator board.
There is no way to determine if dirty or bad data was in the cache and is now lost.
Accelerator status: Temporarily disabled
The array accelerator board has been temporarily disabled.
Check the Disable Code field.
Accelerator status: Unrecognized status
A status returned from the array accelerator board that DAAD does not recognize.
Call your Authorized Compaq Reseller for the latest copy of DAAD.
Accelerator status: Valid data found at reset
Valid data was found in the posted write memory at re-initialization. The data will be flushed
to disk.
This is
not
an error or data loss condition. No action needs to be taken.
Accelerator status: Warranty alert
A catastrophic problem has occurred with the array accelerator board. Refer to the other
messages on the Diagnostics screen for the exact meaning of this message.
Replace the array accelerator board.
Battery pack
X
below reference voltage
The indicated battery pack is below the required voltage levels.
Allow sufficient time for the batteries to recharge (36 hours). If the batteries have not
recharged after 36 hours, replace the battery pack.