HP ProLiant 4500 Compaq ProLiant 4500R Rack-Mountable Servers Maintenance and - Page 64

status = LOOSE CABLE DETECTED

Get HP ProLiant 4500 PDF manuals and user guides View all HP ProLiant 4500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

3-32 Diagnostic Tools Logical Drive X status = FAILED This status could be issued for several reasons. If this logical drive is configured for No Fault Tolerance and one or more drives fail, this status will occur. If mirroring is enabled, and any two mirrored drives fail, this status will occur. If Data Guarding is enabled, and two or more drives fail in this unit, this status will occur. This status may also occur if another configured logical drive is in the WRONG DRIVE REPLACED or LOOSE CABLE DETECTED state. Check for drive failures, wrong drive replaced, or loose cable messages. If there was a drive failure, replace the failed drive(s) and then restore the data for this logical drive from the tape backup. Otherwise, follow the wrong drive replaced or loose cable detected procedures. Logical Drive X status = INTERIM RECOVERY A physical drive in this logical drive has failed. The logical drive is operating in interim recovery mode and is vulnerable. Replace the failed drive as soon as possible. Logical Drive X status = LOOSE CABLE DETECTED A physical drive has a cabling problem. Turn the system off and attempt to reattach the cable onto the drive. If this does not work, replace the cable. Logical Drive X status = NEEDS RECOVER A physical drive in this logical drive has failed and has now been replaced. This drive needs to be rebuilt from the mirror drive or the parity data. When booting up the system, select the "F1 - rebuild drive" option to rebuild the replaced drive. Logical Drive X status = OVERHEATED The temperature of the Intelligent Array Expansion System drives is beyond safe operating levels and it has shut down to avoid damage. Check the fans and the operating environment. Logical Drive X status = OVERHEATING The temperature of the Intelligent Array Expansion System drives is beyond safe operating levels. Check the fans and the operating environment. Logical Drive X status = RECOVERING A physical drive in this logical drive has failed and has now been replaced. The replaced drive is rebuilding from the mirror drive or the parity data. Nothing needs to be done. Normal operations can occur. Maintenance and Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
3-32
Diagnostic Tools
Maintenance and Service Guide
Logical Drive
X
status = FAILED
This status could be issued for several reasons. If this logical drive is configured for No Fault
Tolerance and one or more drives fail, this status will occur. If mirroring is enabled, and any
two mirrored drives fail, this status will occur. If Data Guarding is enabled, and two or more
drives fail in this unit, this status will occur. This status may also occur if another configured
logical drive is in the WRONG DRIVE REPLACED or LOOSE CABLE DETECTED state.
Check for drive failures, wrong drive replaced, or loose cable messages. If there was a drive
failure, replace the failed drive(s) and then restore the data for this logical drive from the tape
backup. Otherwise, follow the wrong drive replaced or loose cable detected procedures.
Logical Drive
X
status = INTERIM RECOVERY
A physical drive in this logical drive has failed. The logical drive is operating in interim
recovery mode and is vulnerable.
Replace the failed drive as soon as possible.
Logical Drive
X
status = LOOSE CABLE DETECTED
A physical drive has a cabling problem.
Turn the system off and attempt to reattach the cable onto the drive. If this does not work,
replace the cable.
Logical Drive
X
status = NEEDS RECOVER
A physical drive in this logical drive has failed and has now been replaced. This drive needs
to be rebuilt from the mirror drive or the parity data.
When booting up the system, select the "F1 - rebuild drive" option to rebuild the
replaced drive.
Logical Drive
X
status = OVERHEATED
The temperature of the Intelligent Array Expansion System drives is beyond safe operating
levels and it has shut down to avoid damage.
Check the fans and the operating environment.
Logical Drive
X
status = OVERHEATING
The temperature of the Intelligent Array Expansion System drives is beyond safe
operating levels.
Check the fans and the operating environment.
Logical Drive
X
status = RECOVERING
A physical drive in this logical drive has failed and has now been replaced. The replaced
drive is rebuilding from the mirror drive or the parity data.
Nothing needs to be done. Normal operations can occur.