HP StorageWorks 1606 HP StorageWorks Fabric OS 6.3.0c Release Notes (5697-0361 - Page 16

/256 SAN Director blade support

Get HP StorageWorks 1606 - Extension SAN Switch PDF manuals and user guides View all HP StorageWorks 1606 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

HP StorageWorks Merging Fabrics Based on M-series and B-series Fibre Channel Switches Application Notes, available at http://www.hp.com. 4 When routing to an M-EOS edge fabric using frame redirection, the fabric must have a Fabric OS-based product in order to configure the frame redirection zone information. 5 When directly attached to a host or target that is part of an encryption flow. 6 Products operating with Fabric OS versions earlier than 5.3.1b or 6.1.0e cannot participate in a logical fabric that is using XISLs (in the base fabric). 7 These platforms cannot be directly attached to hosts or targets for encryption flows. 8 SANRouters 1620 and 2640 should not be used with XPath or Fabric OS-based routing (FCR) for connections to the same edge fabric. 9 Using HP StorageWorks Fabric Manager (FM) 5.5 or earlier with Fabric OS 6.1.1 or later can result in problems with Zoning, Performance monitoring, SYSLOG configuration, FICON wizards, IOD Delay, AAA replication, Port enable/disable and other functions. Unless you are using Admin Domains, HP recommends that you upgrade to HP StorageWorks Data Center Fabric Manager (DCFM) 10.3.x to use with Fabric OS 6.1.1 or later. However, if you are using Admin Domains, HP recommends that you downgrade Fabric OS to 6.1.0h. 10 Fabric Manager is not supported with Fabric OS 6.3.x. 4/256 SAN Director blade support Fabric OS 6.3.0c is fully qualified and supports the Director blades listed in Table 2. Table 2 4/256 SAN Director blade support matrix Director blade FC4-16 FC4-32 FC4-48 FC8-16 FC8-32 FC8-48 FC10-6 Number of blades Supported with any mix, with up to eight blades of each type. No intermix restrictions. The 4/256 SAN Director must run Fabric OS 6.0.0b or later to support the FC816 port blade, and Fabric OS 6.1.0a or later to support the FC8-32 and FC8-48 port blades. FC4-16IP (iSCSI blade) Up to four blades of this type FR4-18i (FCIP/FC Router blade) Up to two blades of this type. Up to eight FR4-18i blades can be installed if they are used only for FC FastWrite or FCIP without routing. 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
HP StorageWorks Merging Fabrics Based on M-series and B-series Fibre Channel Switches Application
Notes
, available at
h
t
tp://w
w
w
.hp
.co
m
.
4
When routing to an M-EOS edge fabric using frame redirection, the fabric must have a Fabric
OS-based product in order to configure the frame redirection zone information.
5
When directly attached to a host or target that is part of an encryption flow.
6
Products operating with Fabric OS versions earlier than 5.3.1b or 6.1.0e cannot participate in a
logical fabric that is using XISLs (in the base fabric).
7
These platforms cannot be directly attached to hosts or targets for encryption flows.
8
SANRouters 1620 and 2640 should not be used with XPath or Fabric OS-based routing (FCR) for
connections to the same edge fabric.
9
Using HP StorageWorks Fabric Manager (FM) 5.5 or earlier with Fabric OS 6.1.1 or later can
result in problems with Zoning, Performance monitoring, SYSLOG configuration, FICON wizards,
IOD Delay, AAA replication, Port enable/disable and other functions. Unless you are using Admin
Domains, HP recommends that you upgrade to HP StorageWorks Data Center Fabric Manager (DCFM)
10.3.
x
to use with Fabric OS 6.1.1 or later. However, if you are using Admin Domains, HP
recommends that you downgrade Fabric OS to 6.1.0h.
10
Fabric Manager is not supported with Fabric OS 6.3.
x
.
4/256 SAN Director blade support
Fabric OS 6.3.0c is fully qualified and supports the Director blades listed in
Table 2
.
Table 2 4/256 SAN Director blade support matrix
Number of blades
Director blade
Supported with any mix, with up to eight blades of each
type. No intermix restrictions. The 4/256 SAN Director
must run Fabric OS 6.0.0b or later to support the FC8-
16 port blade, and Fabric OS 6.1.0a or later to support
the FC8-32 and FC8-48 port blades.
FC4-16
FC4-32
FC4-48
FC8-16
FC8-32
FC8-48
FC10-6
Up to four blades of this type
FC4-16IP (iSCSI blade)
Up to two blades of this type. Up to eight FR4-18i blades
can be installed if they are used only for FC FastWrite
or FCIP without routing.
FR4-18i (FCIP/FC Router blade)
16