HP StorageWorks 1606 HP StorageWorks Fabric OS 6.3.0c Release Notes (5697-0361 - Page 17

DC SAN Backbone and DC04 SAN Director blade support, Power supply requirements for Director blades

Get HP StorageWorks 1606 - Extension SAN Switch PDF manuals and user guides View all HP StorageWorks 1606 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

DC SAN Backbone and DC04 SAN Director blade support Fabric OS 6.3.0c is fully qualified and supports the DC Director blades listed in Table 3. Table 3 DC Director blade support matrix Director blade FC8-16 FC8-32 FC8-48 FC10-6 Number of blades Supported with Fabric OS 6.0.0b or later with any mix, with up to eight blades of each type on the DC SAN Backbone Director. There are no intermix restrictions. The DC04 SAN Director requires Fabric OS 6.2.0a or later, and supports up to four blades. FC4-16IP (iSCSI blade) Not supported with the DC SAN Backbone Director or DC04 SAN Director FR4-18i (FCIP/FC Router blade) Supported with Fabric OS 6.0.0b or later, with a maximum of four blades of this type on the DC SAN Backbone Director. Up to eight FR4-18i blades can be installed if they are used only for FC FastWrite or FCIP without routing on the DC SAN Backbone Director. The DC04 SAN Director requires Fabric OS 6.2.0a or later, and supports up to four blades. FS8-18 (DC Switch Encryption FC blade) Supported with Fabric OS 6.2.0b or later, with a maximum of four blades of this type on the DC SAN Backbone Director or DC04 SAN Director FX8-24 (DC SAN Director Multiprotocol Extension Blade) FCOE10-24 (DC SAN Director Switch 10/24 FCoE Blade) Supported with Fabric OS 6.3.0x, with a maximum of two blades per director. The DC SAN Director Switch 10/24 FCoE Blade can be installed in the same chassis only with FC8-xx and/or FC10-6 blades. It is not supported in the chassis with any other blades. Power supply requirements for Director blades Table 4 lists power supply requirements for Director blades to provide full redundancy (220 VAC power is assumed). HP StorageWorks Fabric OS 6.3.0c Release Notes 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
DC SAN Backbone and DC04 SAN Director blade support
Fabric OS 6.3.0c is fully qualified and supports the DC Director blades listed in
Table 3
.
Table 3 DC Director blade support matrix
Number of blades
Director blade
Supported with Fabric OS 6.0.0b or later with any mix,
with up to eight blades of each type on the DC SAN
Backbone Director. There are no intermix restrictions. The
DC04 SAN Director requires Fabric OS 6.2.0a or later,
and supports up to four blades.
FC8-16
FC8-32
FC8-48
FC10-6
Not supported with the DC SAN Backbone Director or
DC04 SAN Director
FC4-16IP (iSCSI blade)
Supported with Fabric OS 6.0.0b or later, with a maximum
of four blades of this type on the DC SAN Backbone
Director. Up to eight FR4-18i blades can be installed if
they are used only for FC FastWrite or FCIP without routing
on the DC SAN Backbone Director. The DC04 SAN
Director requires Fabric OS 6.2.0a or later, and supports
up to four blades.
FR4-18i (FCIP/FC Router blade)
Supported with Fabric OS 6.2.0b or later, with a maximum
of four blades of this type on the DC SAN Backbone Dir-
ector or DC04 SAN Director
FS8-18 (DC Switch Encryption FC blade)
Supported with Fabric OS 6.3.0x, with a maximum of two
blades per director. The DC SAN Director Switch 10/24
FCoE Blade can be installed in the same chassis only with
FC8-
xx
and/or FC10-6 blades. It is not supported in the
chassis with any other blades.
FX8-24 (DC SAN Director Multiprotocol Extension
Blade)
FCOE10-24 (DC SAN Director Switch 10/24
FCoE Blade)
Power supply requirements for Director blades
Table 4
lists power supply requirements for Director blades to provide full redundancy (220 VAC
power is assumed).
HP StorageWorks Fabric OS 6.3.0c Release Notes
17