HP StorageWorks 1606 HP StorageWorks Fabric OS 6.3.0c Release Notes (5697-0361 - Page 36

Updated command message, Miscellaneous

Get HP StorageWorks 1606 - Extension SAN Switch PDF manuals and user guides View all HP StorageWorks 1606 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

Fabric OS version 6.1.2x and 6.2.0d through 6.3.0x All 8-Gb switches (except 8-Gb 8-Gb SAN Switch for HP SAN Switch for HP BladeSystem BladeSystem c-Class c-Class) All ports default to idle [mode 0] regardless of what FOS was previously installed, unless manually changed to arb(ff) previously [mode 1], then it will remain arb(ff). Can be changed by the user. • If 6.2.0d was installed in the factory, all internal ports remain at arb(ff) [mode 1], external ports at idle [mode 0]. Can be changed by the user. • If pre-6.2.0d was installed in the factory, all internal and external ports remain at idle [mode 0], unless they were manually changed to arb(ff) [mode 1], then they remain at arb(ff). Can be changed by the user. Mode: 0-IDLE for Link Init, IDLE for fill word 1-ARB(FF) for Link Init, ARB(FF) for fill word (NOTE: not supported with XP storage arrays) 16.1.2x was not supported on EVA4400 embedded switch module. 26.1.2x was not supported on this switch. Updated command message When executing the lscfg --create command with the following syntax: switch_128:FID128:admin> lscfg --create 1 About to create switch with fid=1. Please wait... Logical Switch with FID (1) has been successfully created. You should expect to see the following revised message: Logical Switch has been created with default configurations. Please configure the Logical Switch with appropriate switch and protocol settings before activating the Logical Switch. Miscellaneous After changing domain offset followed by issuing an hafailover command on a DC SAN Backbone Director, DC04 SAN Director, or 4/256 SAN Director running Fabric OS 6.3 in interopmode 2, the console log may generate continuous Unknown LSR type messages. You must either reboot the switch or issue another hafailover command to terminate the messages. During non-disruptive firmware upgrades, E_Ports in R-RDY mode may cause some frame drops on the E-Port links. 36

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
8-Gb SAN Switch for HP
BladeSystem c-Class
All 8-Gb switches (except 8-Gb
SAN Switch for HP BladeSystem
c-Class)
Fabric OS version
•
If 6.2.0d was installed in the
factory, all internal ports remain
at arb(ff) [mode 1], external
ports at idle [mode 0]. Can be
changed by the user.
•
If pre-6.2.0d was installed in the
factory, all internal and external
ports remain at idle [mode 0],
unless they were manually
changed to arb(ff) [mode 1],
then they remain at arb(ff). Can
be changed by the user.
All ports default to idle [mode 0]
regardless of what FOS was previ-
ously installed, unless manually
changed to arb(ff) previously [mode
1], then it will remain arb(ff). Can
be changed by the user.
6.1.2x and 6.2.0d through
6.3.0x
0
—
IDLE for Link Init, IDLE for fill
word
1
—
ARB(FF) for Link Init, ARB(FF) for
fill word (NOTE: not supported with
XP storage arrays)
Mode:
1
6.1.2x was not supported on EVA4400 embedded switch module.
2
6.1.2x was not supported on this switch.
Updated command message
When executing the
lscfg --create
command with the following syntax:
switch_128:FID128:admin> lscfg --create 1 About to create switch with
fid=1. Please wait... Logical Switch with FID (1) has been successfully
created
.
You should expect to see the following revised message:
Logical Switch has been created with default configurations. Please
configure the Logical Switch with appropriate switch and protocol settings
before activating the Logical Switch.
Miscellaneous
After changing domain offset followed by issuing an
hafailover
command on a DC SAN Backbone
Director, DC04 SAN Director, or 4/256 SAN Director running Fabric OS 6.3 in interopmode 2, the
console log may generate continuous
Unknown LSR type
messages. You must either reboot the
switch or issue another
hafailover
command to terminate the messages.
During non-disruptive firmware upgrades, E_Ports in R-RDY mode may cause some frame drops on
the E-Port links.
36