HP StorageWorks 1606 HP StorageWorks Fabric OS 6.3.0c Release Notes (5697-0361 - Page 61

FOS-FVT- If a Read is Sent Busy Status and the Subsequent Seek is also

Get HP StorageWorks 1606 - Extension SAN Switch PDF manuals and user guides View all HP StorageWorks 1606 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Ipaddrset command to set Lance GE ports IP address is non-responsive. Must reboot active CP to activate IP. Fixed in Fabric OS 6.3.0 Workaround prior to code change: The following should work. Following any removal or relocation of an encryption blade from any chassis slot, do an hafailover to cause the standby CP to become active. This should be done even if no change in chassis IP addresses is required as other problems could be otherwise encountered, depending on network configuration. Optimized SERDES setting for Brocade 8 Gb SAN Switch for BladeSystem c-Class. If TI zone operations are performed simultaneously on different switches, active CP may failover due to termination of Name server module. Fixed in Fabric OS 6.3.0 Fixed in Fabric OS 6.3.0 Workaround prior to code change: No workaround needed, the DC SAN Director CP fails over non-disruptively and retains all configuration data. 4 Gb switch running at fixed 2 Gb speed may not respond to FLOGI from HBA using auto-speed negotiation. Fixed in Fabric OS 6.3.0 Workaround prior to code change: Lock the port to fixed speed. Detected termination of management server daemon during stress testing on DC SAN Director with 8 logical switches. Fixed in Fabric OS 6.3.0 Workaround prior to code change: Wait for system to stabilize after executing bladedisable and before issuing hafailover or disable MS platform services while performing stress testing. FOS-FVT- If a Read is Sent Busy Status and the Subsequent Seek is also Fixed in Fabric OS 6.3.0 Sent Busy, Mis-Compares To the Host. Downloading config file between switches causes license lost. Fixed in Fabric OS 6.3.0 Workaround prior to code change: Do the following to back up licenses: 1. Execute licenseshow command save the licenses into a file outside the switch. 2. Then perform configdownload. 3. Add the licenses saved in step one. Inconsistent display of urouteshow trying to map to invalid FCR user Fixed in Fabric OS 6.3.0 port while topologyshow is not showing those routes. If user account on RADIUS server is set up with only Chassis level role as primary, but it is not on the LF role list, the user cannot login. Fixed in Fabric OS 6.3.0 Workaround prior to code change: Specify LF role list in the RADIUS server for the account. Missing Pause and Resume for EX port having MiI10K Edge Fabric in Fixed in Fabric OS 6.3.0 239 Domain - works for domain 209-238. HP StorageWorks Fabric OS 6.3.0c Release Notes 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
Fixed in Fabric OS 6.3.0
Workaround prior to code change:
The following should work. Following
any removal or relocation of an
encryption blade from any chassis
slot, do an
hafailover
to cause the
standby CP to become active. This
should be done even if no change in
chassis IP addresses is required as
other problems could be otherwise
encountered, depending on network
configuration.
Ipaddrset
command to set Lance GE ports IP address is non-respons-
ive. Must reboot active CP to activate IP.
Fixed in Fabric OS 6.3.0
Optimized SERDES setting for Brocade 8 Gb SAN Switch for
BladeSystem c-Class.
Fixed in Fabric OS 6.3.0
Workaround prior to code change:
No workaround needed, the DC SAN
Director CP fails over non-disruptively
and retains all configuration data.
If TI zone operations are performed simultaneously on different
switches, active CP may failover due to termination of Name server
module.
Fixed in Fabric OS 6.3.0
Workaround prior to code change:
Lock the port to fixed speed.
4 Gb switch running at fixed 2 Gb speed may not respond to FLOGI
from HBA using auto-speed negotiation.
Fixed in Fabric OS 6.3.0
Workaround prior to code change:
Wait for system to stabilize after
executing
bladedisable
and
before issuing
hafailover
or
disable MS platform services while
performing stress testing.
Detected termination of management server daemon during stress
testing on DC SAN Director with 8 logical switches.
Fixed in Fabric OS 6.3.0
FOS-FVT- If a Read is Sent Busy Status and the Subsequent Seek is also
Sent Busy, Mis-Compares To the Host.
Fixed in Fabric OS 6.3.0
Workaround prior to code change:
Do the following to back up licenses:
1. Execute
licenseshow
command
save the licenses into a file outside the
switch. 2. Then perform
configdownload
. 3. Add the
licenses saved in step one.
Downloading
config
file between switches causes license lost.
Fixed in Fabric OS 6.3.0
Inconsistent display of
urouteshow
trying to map to invalid FCR user
port while
topologyshow
is not showing those routes.
Fixed in Fabric OS 6.3.0
Workaround prior to code change:
Specify LF role list in the RADIUS
server for the account.
If user account on RADIUS server is set up with only Chassis level role
as primary, but it is not on the LF role list, the user cannot login.
Fixed in Fabric OS 6.3.0
Missing Pause and Resume for EX port having MiI10K Edge Fabric in
239 Domain - works for domain 209-238.
HP StorageWorks Fabric OS 6.3.0c Release Notes
61