Icom IC-R6 Instruction Manual - Page 32

Memory channel programming

Get Icom IC-R6 PDF manuals and user guides View all Icom IC-R6 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

5 MEMORY CHANNELS ■ Memory channel programming q Push [V/M] to select the VFO mode. w Set a desired frequency: ➥ Select a desired band with [BAND]. ➥ Set a desired frequency with [DIAL]. ➥ Set other data (e.g. frequency offset, duplex direction, tone squelch, etc.), if desired. e H old down [S.MW](V/M) for 1 second to enter the select memory write mode. • 1 short and 1 long beep sounds. • The " " icon and memory channel number blink. r Rotate [DIAL] to select a desired channel. • Scan edge channels 00A/B to 24A/B can also be selected. • While holding down [FUNC], rotate [DIAL] to select memory channels in 10 channel steps. t Hold down [S.MW](V/M) for 1 second. • 3 beeps sound. • The memory channel number automatically increases if you continue to hold down [S.MW](V/M) after programming. NOTE: Push [V/M] to cancel programming and exit the select memory write mode, before memory programming is finished. [EXAMPLE]: Programming 145.870 MHz into memory channel 20 (a blank channel). Hold down for 1 sec. Rotate to select channel 20. The VFO mode Enter the select memory write mode. Hold down for 1 sec. to program. Return to the VFO mode. 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
19
5
MEMORY CHANNELS
■
Memory channel programming
q
Push
[V/M]
to select the VFO mode.
w
Set a desired frequency:
➥
Select a desired band with
[BAND]
.
➥
Set a desired frequency with
[DIAL]
.
➥
Set other data
(e.g. frequency offset, duplex direction, tone
squelch, etc.)
, if desired.
e
Hold down
[S.MW]
(V/M) for 1 second to enter the select
memory write mode.
• 1 short and 1 long beep sounds.
• The “
” icon and memory channel number blink.
r
Rotate
[DIAL]
to select a desired channel.
• Scan edge channels 00A/B to 24A/B can also be selected.
• While holding down
[FUNC]
, rotate
[DIAL]
to select memory
channels in 10 channel steps.
t
Hold down
[S.MW]
(V/M) for 1 second.
• 3 beeps sound.
• The memory channel number automatically increases if you
continue to hold down
[S.MW]
(V/M) after programming.
NOTE:
Push
[V/M]
to cancel programming and exit the
select memory write mode, before memory programming
is finished.
Rotate
Hold down
for 1 sec.
to select channel 20.
Hold down
for 1 sec. to program.
The VFO mode
Enter the select memory write mode.
Return to the VFO mode.
[EXAMPLE]:
Programming 145.870 MHz into memory channel 20 (a blank channel).