Icom IC-R6 Instruction Manual - Page 43

Scan edges programming

Get Icom IC-R6 PDF manuals and user guides View all Icom IC-R6 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

SCAN OPERATION 6 ■ Scan edges programming 1 Scan edges can be programmed in the same manner as r R otate [DIAL] to select a desired programmed scan edge 2 memory channels. Scan edges are programmed into scan channel from 00A to 24A. 3 edge memory channels, 00A/00B to 24A/24B. t Hold down [S.MW](V/M) for 1 second. • 3 beeps sound 4 q Push [V/M] to select the VFO mode. w Set a desired frequency: • The matched "B" channel is automatically selected if you continue to hold down [S.MW](V/M) after programming. 5 ➥ Push [BAND] to select a desired band. y T o program a frequency for the other pair of scan edges, 6 ➥ Rotate [DIAL] to set a desired frequency. ➥ Set other data (e.g. frequency offset, duplex direction, tone 00B or 24B, repeat steps w and t. • If the same frequency is programmed into a pair of scan edges, 7 squelch, etc.), if desired. the programmed scan will not function. 8 e H old down [S.MW](V/M) for 1 second to enter the select memory write mode. 9 • 1 short and 1 long beep sounds. 10 • The " " icon and memory channel number blink. 11 [EXAMPLE]: Programming 145.370 MHz into scan edge channel 03A (a blank channel). 12 Hold down for 1 sec. Rotate to select channel 03A. 13 14 15 The VFO mode Enter the select memory write mode. 16 Hold down for 1 sec. to program. Return to the VFO mode. 30

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
30
6
SCAN OPERATION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
■
Scan edges programming
Scan edges can be programmed in the same manner as
memory channels. Scan edges are programmed into scan
edge memory channels, 00A/00B to 24A/24B.
q
Push
[V/M]
to select the VFO mode.
w
Set a desired frequency:
➥
Push
[BAND]
to select a desired band.
➥
Rotate
[DIAL]
to set a desired frequency.
➥
Set other data
(e.g. frequency offset, duplex direction, tone
squelch, etc.)
, if desired.
e
Hold down
[S.MW]
(V/M) for 1 second to enter the select
memory write mode.
• 1 short and 1 long beep sounds.
• The “
” icon and memory channel number blink.
r
Rotate
[DIAL]
to select a desired programmed scan edge
channel from 00A to 24A.
t
Hold down
[S.MW]
(V/M) for 1 second.
• 3 beeps sound
• The matched “B” channel is automatically selected if you con-
tinue to hold down
[S.MW]
(V/M) after programming.
y
To program a frequency for the other pair of scan edges,
00B or 24B, repeat steps
w
and
t
.
• If the same frequency is programmed into a pair of scan edges,
the programmed scan will not function.
Rotate
Hold down
for 1 sec.
to select channel 03A.
Hold down
for 1 sec. to program.
The VFO mode
Enter the select memory write mode.
Return to the VFO mode.
[EXAMPLE]:
Programming 145.370 MHz into scan edge channel 03A (a blank channel).