Icom IC-R6 Instruction Manual - Page 74

Data cloning - programming cable

Get Icom IC-R6 PDF manuals and user guides View all Icom IC-R6 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

10 OTHER FUNCTIONS ■ Data cloning Cloning allows you to quickly and easily transfer the programmed contents from one receiver to another; or data from a personal computer to a receiver, using the optional CS-R6 cloning software and the appropriate cloning cable. D Cloning between receivers q C onnect the OPC-474 cloning cable to the [SP] jack of the master and sub-receivers. • The master receiver is used to send data to the sub-receiver. to [SP] to [SP] Master receiver Sub receiver NOTE: DO NOT push any key on the sub-receiver during cloning. This will cause a cloning error. w H old down [V/M] of only the master receiver, and then turn it ON. For the sub-receiver, simply turn it ON. (See below for more information.) "CLONE" and "m" appear when entered the cloning mode. Master receiver ✔ CLONING MODE ENTRY (except Master receiver): When the CI-V baud rate (p. 56) is selected any other than "9600" or "AUTO," the following operations are required. q Turn the receiver's power OFF. w While holding down [MODE], push and hold [ ] for 1 sec- ond to enter the cloning mode. 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
61
10
OTHER FUNCTIONS
■
Data cloning
Cloning allows you to quickly and easily transfer the pro-
grammed contents from one receiver to another; or data from
a personal computer to a receiver, using the optional CS-R6
CLONING
SOFTWARE
and the appropriate cloning cable.
D±
Cloning between receivers
q
Connect the OPC-474 cloning cable to the [SP] jack of the
master and sub-receivers.
• The master receiver is used to send data to the sub-receiver.
to [SP]
Master
receiver
Sub
receiver
to [SP]
NOTE: DO NOT
push any key on the sub-receiver during
cloning. This will cause a cloning error.
w
Hold down
[V/M]
of only the master receiver, and then
turn it ON. For the sub-receiver, simply turn it ON. (See
below for more information.)
“CLONE” and “m” appear
when entered the cloning
mode.
Master receiver
✔
CLONING MODE ENTRY (except Master receiver):
When the CI-V baud rate (p. 56) is selected any other than
“9600” or “AUTO,” the following operations are required.
q
Turn the receiver’s power OFF.
w
While holding down
[MODE]
, push and hold
[
]
for 1 sec-
ond to enter the cloning mode.