Lenovo J105 Hardware Maintenance Manual - Page 115

Replacing, diskette, drive

Get Lenovo J105 PDF manuals and user guides View all Lenovo J105 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 115 highlights

Replacing the diskette drive 1. Remove the left-side and right-side covers. See "Removing the covers" on page 82. 2. Disconnect the signal and power cables from the rear of the hard disk drive. Note: You will probably have to disconnect cables that are connected to the system board and other drives to allow the diskette drive to be removed from inside the chassis. 3. Remove the two screws that secure the drive on each side. 4. Slide the drive toward the rear of the chassis until it can be removed. 5. Slide the new drive into the bay until the screws holes on each side are aligned and install two screws in each side of the drive. 6. Reconnect all signal and power cables that were disconnected. See "Identifying parts on the system board" on page 85. 7. Go to "Completing the FRU replacement." on page 111. Chapter 8. Replacing FRUs (Types 8252, 8253, 8254, 8255, 8256, 8257, 8258, and 8259) 109

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
Replacing
the
diskette
drive
1.
Remove
the
left-side
and
right-side
covers.
See
“Removing
the
covers”
on
page
82.
2.
Disconnect
the
signal
and
power
cables
from
the
rear
of
the
hard
disk
drive.
Note:
You
will
probably
have
to
disconnect
cables
that
are
connected
to
the
system
board
and
other
drives
to
allow
the
diskette
drive
to
be
removed
from
inside
the
chassis.
3.
Remove
the
two
screws
that
secure
the
drive
on
each
side.
4.
Slide
the
drive
toward
the
rear
of
the
chassis
until
it
can
be
removed.
5.
Slide
the
new
drive
into
the
bay
until
the
screws
holes
on
each
side
are
aligned
and
install
two
screws
in
each
side
of
the
drive.
6.
Reconnect
all
signal
and
power
cables
that
were
disconnected.
See
“Identifying
parts
on
the
system
board”
on
page
85.
7.
Go
to
“Completing
the
FRU
replacement.”
on
page
111.
Chapter
8.
Replacing
FRUs
(Types
8252,
8253,
8254,
8255,
8256,
8257,
8258,
and
8259)
109