Netgear FM114P FR114W Reference Manual - Page 116

Power LED Not On, Test LED Never Turns On or Test LED Stays

Get Netgear FM114P - Cable/DSL ProSafe 802.11b Wireless Firewall Router PDF manuals and user guides
UPC - 606449024029
View all Netgear FM114P manuals
Add to My Manuals
Save this manual to your list of manuals

Page 116 highlights

Reference Manual for the Model FR114P, FR114W and FM114P Cable/DSL ProSafe Firewall Family b. The Local port Link LEDs are lit for any local ports that are connected. c. The Internet Link port LED is lit. If a port's Link LED is lit, a link has been established to the connected device. If a port is connected to a 100 Mbps device, verify that the port's 100 LED is lit. If any of these conditions does not occur, refer to the appropriate following section. Power LED Not On If the Power and other LEDs are off when your firewall is turned on: • Make sure that the power cord is properly connected to your firewall and that the power supply adapter is properly connected to a functioning power outlet. • Check that you are using the 12VDC power adapter supplied by NETGEAR for this product. If the error persists, you have a hardware problem and should contact technical support. Test LED Never Turns On or Test LED Stays On When the firewall is turned on, the Test LED turns on for about 10 seconds and then turns off. If the Test LED does not turn on, or if it stays on, there is a fault within the firewall. If you experience problems with the Test LED: • Cycle the power to see if the firewall recovers and the LED blinks for the correct amount of time. If all LEDs including the Test LED are still on one minute after power up: • Cycle the power to see if the firewall recovers. • Clear the firewall's configuration to factory defaults. This will set the firewall's IP address to 192.168.0.1. This procedure is explained in "Using the Default Reset button" on page 10-8. If the error persists, you might have a hardware problem and should contact technical support. Local or Internet Port Link LEDs Not On If either the Local or Internet Port Link LEDs do not light when the Ethernet connection is made, check the following: 10-2 Troubleshooting

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
Reference Manual for the Model FR114P, FR114W and FM114P Cable/DSL ProSafe Firewall Family
10-2
Troubleshooting
b.
The Local port Link LEDs are lit for any local ports that are connected.
c.
The Internet Link port LED is lit.
If a port’s Link LED is lit, a link has been established to the connected device. If a port is
connected to a 100 Mbps device, verify that the port’s 100 LED is lit.
If any of these conditions does not occur, refer to the appropriate following section.
Power LED Not On
If the Power and other LEDs are off when your firewall is turned on:
•
Make sure that the power cord is properly connected to your firewall and that the power
supply adapter is properly connected to a functioning power outlet.
•
Check that you are using the 12VDC power adapter supplied by NETGEAR for this product.
If the error persists, you have a hardware problem and should contact technical support.
Test LED NeverTurns On or Test LED Stays On
When the firewall is turned on, the Test LED turns on for about 10 seconds and then turns off. If
the Test LED does not turn on, or if it stays on, there is a fault within the firewall.
If you experience problems with the Test LED:
•
Cycle the power to see if the firewall recovers and the LED blinks for the correct amount of
time.
If all LEDs including the Test LED are still on one minute after power up:
•
Cycle the power to see if the firewall recovers.
•
Clear the firewall’s configuration to factory defaults. This will set the firewall’s IP address to
192.168.0.1. This procedure is explained in
“Using the Default Reset button“ on page 10-8
.
If the error persists, you might have a hardware problem and should contact technical support.
Local or Internet Port Link LEDs Not On
If either the Local or Internet Port Link LEDs do not light when the Ethernet connection is made,
check the following: