Onkyo TX-RZ800 User Manual - Page 108
RI Dock, Others, En-72
View all Onkyo TX-RZ800 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 108 highlights
RI Dock ●● Make sure the unit is turned on, the correct input source is selected, and the volume is turned up. ●● Make sure cord and cable plugs are properly plugged in. ●● Make sure your iPod/iPhone is properly inserted in the Dock. If your iPod/iPhone is in a case, it may not connect properly to the Dock. Always remove your iPod/ iPhone from the case before inserting it into the Dock. Try reconnecting your iPod/iPhone. ●● Make sure your iPod/iPhone is actually playing. If the above does not solve the problem, check the following. There is no sound ●● Try resetting your iPod/iPhone. There is no video ●● Make sure the correct input is selected on your TV or the unit. ●● Make sure that your iPod/iPhone model's TV OUT setting is set to On. ●● Some versions of the iPod/iPhone do not output video. The AV receiver's remote controller does not control your iPod/iPhone ●● The iPod/iPhone cannot be operated while it is displaying the Apple logo. ●● Make sure you have selected the correct remote controller mode. ●● When you use the AV receiver's remote controller, point it toward this unit. ●● Before operating with the remote controller, you may need to play on your iPod/iPhone to make the input selector be recognized. ●● Depending on your iPod/iPhone model and generation, some buttons may not work as expected. ●● Try resetting your iPod/iPhone. The unit unexpectedly selects your iPod/iPhone as the input source ●● Always pause iPod/iPhone playback before selecting a different input source. If playback is not paused, the Direct Change function may select your iPod/iPhone as the input source by mistake during the transition between tracks. En-72 Others Strange noises can be heard from the unit ●● If you have connected another unit to the same wall outlet as this unit, this noise may be an effect from the other unit. If the symptoms improve by unplugging the power cord of the other unit, use different wall outlets for this unit and the other unit. When performing Automatic Speaker Setup, the measurement fails and the message "Ambient noise is too high." is displayed ●● This can be caused by a malfunction in your speaker unit. Check if the unit produces normal sounds. The Late Night function does not work ●● Make sure the source material is Dolby Digital, Dolby Digital Plus, Dolby TrueHD, or DTS. Re-EQ, Re-EQ(THX) function does not work ●● This function can be used in the following listening modes: Dolby Digital, Dolby Digital Plus, Dolby TrueHD, Multichannel, DTS, DTS-ES, DTS 96/24, DTS-HD High Resolution Audio, DTS-HD Master Audio, DTS Express, DSD. ●● In Re-EQ(THX), the following listening modes can be used: THX Cinema, THX Surround EX, and THX Select2 Cinema. How do I change the language of a multiplex source ●● Select "Main" or "Sub" for "3. Audio Adjust" - "Multiplex/ Mono" - "Multiplex Input Channel". Cannot connect to the AV receiver from a Web browser ●● Make sure that the IP address of the AV receiver is correctly input to the Internet browser. ●● When DHCP is used for allocating the IP address, the IP address of this AV receiver may have been changed. ●● Make sure that both AV receiver and PC are properly connected to the network. Power consumption in standby mode ●● In the following cases, the power consumption in standby mode may reach up to a maximum of 16.2 W: - When "USB Power Out at Standby", "Network Standby" or "Bluetooth Wakeup" is set to "On". - When "HDMI CEC (RIHD)" is set to "On". (Depending on the TV status, this unit will enter normal standby mode) - The "HDMI Standby Through" setting is set to other than "Off". Troubleshooting