Onkyo TX-RZ800 User Manual - Page 92

TV operation, En-56

Get Onkyo TX-RZ800 PDF manuals and user guides View all Onkyo TX-RZ800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 92 highlights

„„Remapping the Colored Buttons The colored button assignment on the AV receiver's remote controller can be remapped to match that on the remote controller of the component whose remote control code you programmed to REMOTE MODE. However, you will not be able to remap the colored buttons if Zone 2/Zone 3 is selected. 1. Hold down the REMOTE MODE button to map and A (Red) simultaneously until the remote indicator lights (about 3 seconds). ●● Remapping is possible only for codes included in the categories of the Remote Control Code List (DVD player, TV, etc.) Operating Other Components with the Remote Controller „„Resetting the REMOTE MODE Buttons You can reset the remote control code registered in the REMOTE MODE button to its default status. This operation can be executed on a single REMOTE MODE button. 1. Press and hold Q for 3 or more seconds while holding down the REMOTE MODE button you want to reset. ●● The remote indicator will light. TV operation Press the REMOTE MODE button programmed with the remote control code for the relevant AV component to switch the remote controller mode to that for the AV component. Then, operate by using the corresponding buttons. Available buttons vary depending on the product category of the component. Operation may be incorrect or impossible depending on the product. 1 2. Within 30 seconds, press the REMOTE MODE button again. 3 ●● Resetting is complete when the remote indicator flashes twice. 2 4 To reset all the remote controller settings: While holding down RCV, press and hold Q for 3 or more seconds until the remote indicator stays lit. Within 30 seconds, press RCV again. Resetting is complete when the remote indicator flashes twice. 1 REMOTE MODE 2 , INPUT, VOL / 3 MUTING 4 CH +/- 2. Within 30 seconds, press the colored buttons from left to right, in the order you want to remap. ●● For example, if the colored buttons on the remote controller of the other component are yellow, green, blue, and red from left to right, press the buttons on the AV receiver's remote controller in that order. ●● Programming is complete when the remote indicator flashes twice. The remote indicator flashes once slowly when programming the remote control code fails. Try programming again. ●● Pressing any other button than a colored button cancels the remap operation. 5 8 6 9 7 5 GUIDE 6 / / / , ENTER 7 HOME 8 PREV CH 9 RETURN En-56

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
Operating Other Components with the Remote Controller
En-56
±
Remapping the Colored Buttons
The colored button assignment on the AV receiver's remote
controller can be remapped to match that on the remote
controller of the component whose remote control code you
programmed to REMOTE MODE. However, you will not
be able to remap the colored buttons if Zone 2/Zone 3 is
selected.
1. Hold down the REMOTE MODE button to map and A
(Red) simultaneously until the remote indicator lights
(about 3 seconds).
●
Remapping is possible only for codes included in the
categories of the Remote Control Code List (DVD
player, TV, etc.)
2. Within 30 seconds, press the colored buttons from left to
right, in the order you want to remap.
●
For example, if the colored buttons on the remote
controller of the other component are yellow, green,
blue, and red from left to right, press the buttons on
the AV receiver's remote controller in that order.
●
Programming is complete when the remote indicator
flashes twice. The remote indicator flashes once
slowly when programming the remote control code
fails. Try programming again.
●
Pressing any other button than a colored button
cancels the remap operation.
±
Resetting the REMOTE MODE Buttons
You can reset the remote control code registered in the
REMOTE MODE button to its default status. This operation
can be executed on a single REMOTE MODE button.
1. Press and hold Q for 3 or more seconds while holding
down the REMOTE MODE button you want to reset.
●
The remote indicator will light.
2. Within 30 seconds, press the REMOTE MODE button
again.
●
Resetting is complete when the remote indicator
flashes twice.
To reset all the remote controller settings
: While holding
down RCV, press and hold Q for 3 or more seconds until
the remote indicator stays lit. Within 30 seconds, press
RCV again. Resetting is complete when the remote
indicator flashes twice.
TV operation
Press the REMOTE MODE button programmed with
the remote control code for the relevant AV component
to switch the remote controller mode to that for the AV
component. Then, operate by using the corresponding
buttons. Available buttons vary depending on the product
category of the component. Operation may be incorrect or
impossible depending on the product.
1
2
3
4
1
REMOTE MODE
2
, INPUT, VOL
/
3
MUTING
4
CH +/–
5
8
9
6
7
5
GUIDE
6
/
/
/
, ENTER
7
HOME
8
PREV CH
9
RETURN