Onkyo TX-RZ800 User Manual - Page 14
Remote Mode Setup, 4 Network Connection - arc
View all Onkyo TX-RZ800 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 14 highlights
Source Connection The following CEC-compatible devices are found; Do you wish to turn on the CEC link? xxxxxxxxxxx Yes No SETUP Exit If you select "Yes", the connection with ARC compatible TV and HDMI Standby Through function will be set to "On" and enabled. 3 Remote Mode Setup Initial Setup Remote Mode Setup ɹPreprograming remote will give you control ɹof other devices from AV receiver remote. ɹWould you like to setup your remote to ɹcontrol your devices? This may take a while ɹdepending on what and how many you have ɹconnected. You can always come back to remote ɹsetup from setup "7-2 Remote Mode Setup". ɹYes, Continue ɹNo, Skip SETUP Exit You can enable operation of the other components using the remote controller of the unit. When the Remote Mode Setup start screen is displayed, select "Yes, Continue" with the cursors and press ENTER on the remote controller. Follow the guidance to select the desired REMOTE MODE button and in the keyboard screen, enter the first three characters of the brand name of the device you are going to program and search for the remote control code. The guidance will also explain how to set the remote controller. En-14 4 Network Connection Initial Setup Network Connection ɹDo you want to connect network connection? ɹIt gives you network services that our AV ɹreceiver support. If you wish to skip this step. ɹselect "No. Skip". ɹYes ɹNo, Skip SETUP Exit You can check the network connection and make the WiFi setting. When the Network Connection start screen is displayed, select "Yes" with the cursors and press ENTER on the remote controller. If you select "Wired" in the next screen, you can view the LAN cable connection status. To make the Wi-Fi setting, select "Wireless", press ENTER on the remote controller and follow the sections below. Step 2: Initial Setup ˙ If you selected "Scan Networks" 2. Select the SSID of the access point to be connected with the cursor buttons and press ENTER. When the SSID of the access point appears on the TV screen, select the desired access point. ・ If you changed the initial setting of the access point to skip password entry, step 3 is unnecessary. ・ If you changed the initial setting of the access point to hide the SSID, see "When the access point is not displayed". 3. Select and set the authentication method. The "Enter Password" screen may be displayed automatically if the wireless LAN router does not have an automatic setting button. Wi-Fi Setup Select the authentication method. Enter Password Push Button PIN code Make the following preparations. Wi-Fi connection requires an access point such as wireless LAN router (Ú). Write down the SSID and password (key) of the access point if they are shown in the label of the main body. If the access point has an automatic setting button (may be called differently according to the manufacturer), you can set up without inputting the password. For how to use the automatic setting button of the access point, refer to its instruction manual. * The unit supports Wi-Fi connection with 2.4 GHz access point. 1. Select the method of Wi-Fi connection with the cursors and press ENTER. Scan Networks: Search for an access point such as a wireless LAN router from this unit. Use iOS Device (iOS7 or later): If you are using an iOS device, you can connect easily with Wi-Fi just by sharing the iOS device's Wi-Fi settings with this unit. When this screen is displayed, select and set one of the three authentication methods: "Enter Password", "Push Button" and "PIN code". See below for details of and how to set each method. Enter Password: Enter the password of the access point to establish connection. 1 Select "Enter Password" with the cursor buttons and press ENTER. 2 Enter the password (Ú) on the keyboard screen, select "OK" with the cursor buttons and press ENTER. * Select "A/a" and press ENTER to toggle between upper and lower case. Select "" or "" and press ENTER to move the cursor to the selected direction. Select and press ENTER to delete the character at the left of the cursor position. To select whether to mask the password with "Ú" or display it in plain text, press D on the remote control. Press +10 on the remote controller to switch between upper and lower case. Press CLR to delete all the input characters. 3 If the security method of the access point to be connected is WEP, select "Default Key ID", and press ENTER.