Onkyo TX-RZ800 User Manual - Page 13
Source Connection, Step 2, Initial Setup
View all Onkyo TX-RZ800 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 13 highlights
* Correct measurement will not be possible if the microphone is held by hand. Measurement is not possible if headphones are being used. * The subwoofer sound may not be detected since it is extremely low frequencies. Set the subwoofer volume to around the half of its maximum volume. * Measurement may be interrupted if there is ambient noise or radio frequency interference. If this occurs, close the window and turn off the home appliance and fluorescent light. 2. After placing the microphone at the measurement position, select "Do it Now" with the cursors and press ENTER. 3. When "Please plug microphone that came in a box with AV receiver" is displayed, connect the microphone to the SETUP MIC jack of the unit. SETUP MIC jack Calibration microphone 4. Set the speakers you have connected and the type of Height Speakers. AccuEQ Room Calibration Speaker Channels Subwoofer Height Speaker Bi-Amp Powered Zone2 7.1ch Yes ----No No Select how many speakers you have. ENTER Next When the screen above is displayed, set the items with the cursors on the remote controller. The image on the screen changes as you choose the number of channels in "Speaker Channels", so refer to it when performing the settings. After completing all the settings, press ENTER on the remote controller. After this, follow the guidance displayed on the TV screen. ・ When the cursor is on an item, the content of the item will be shown in the lower part of the screen. 5. The test tones sound from the connected speakers and automatic speaker setting starts. Measurement will be made three or more times for each speaker. It takes several minutes to be completed. Keep the room as quiet as possible during measurement. If any of the speakers do not produce the test tone, check for disconnection. ・ During measurement, each speaker outputs the test tones at a high volume. Be careful of sound leak that may disturb your neighbors, or be careful not to frighten young children. 6. When the measurement is completed, the measurement result is displayed. Press t/u on the remote controller to check the settings. Press ENTER with "Save" selected. To have the settings reflected for all the speakers, select "On (All Channels)" in the next screen and press ENTER on the remote controller. ・ Select "On (Except Front Left / Right)" to disable just the front speakers. ・ If there is an error message, follow the on-screen instruction to remove the error cause. If the subwoofer was not detected, turn the volume of the subwoofer up to maximum and then select "Retry". About THX playback THX recommends setting the speakers manually if you use THX-certified speakers or playing back with THX listening modes. ・ THX recommends setting the crossover frequency to "80Hz(THX)" manually. ・ Due to the electrical complexities and the interaction with the room, you may notice irregular results when setting the level or distance of each speaker. If this happens, THX recommends setting the speakers and the subwoofer manually. 7. When "Please unplug setup microphone." is displayed, disconnect the microphone. Step 2: Initial Setup 2 Source Connection You can check the connections for each of the inputs and configure the HDMI link function. 1. When the Source Connection start screen is displayed, select "Yes, Continue" with the cursors and press ENTER. Initial Setup Source Connection ɹThis step will start to check if the ɹconnections were made correctly. ɹWould you like to continue? Yes. Continue No. Skip SETUP Exit 2. Select the desired input to check the connection and press ENTER. Start playback of the selected device. If connection is correct, video/audio of the input source selected on the unit will be played. 3. After checking the connection, select "Yes" with the cursors and press ENTER. ・ If you select "No" and press ENTER, the error cause will be displayed. Follow the guidance to remove the error cause and check the connection again. 4. Select "Yes" with the cursors and press ENTER on the remote controller to check the connection of other inputs or select "No, Done Checking" and press ENTER to skip. If you select "Yes", you will return to the screen of step 2. If you select "No, Done Checking", you will proceed to step 5. 5. Settings for the CEC link function. To enable the HDMI link function with CEC compatible equipment, select "Yes", then select "Yes" again in the next screen. En-13