Panasonic AG-HMC70 Memory Card Camera Recorder - Page 112

Problem, Check points, not shown.

Get Panasonic AG-HMC70 - AVCHD 3CCD Flash Memory Professional Camcorder PDF manuals and user guides
UPC - 092281893525
View all Panasonic AG-HMC70 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 112 highlights

Others Problem This unit cannot be operated though powered up. This unit does not operate normally. The remote control does not function. A function indication such as the remaining time indication or the elapsed time indication is not shown. Recording does not start although power is supplied to this unit and the SD card is correctly inserted. The unit arbitrarily stops recording. Check points ≥Press the RESET button. (l 115) If normal conditions are not restored yet, remove the battery or AC adaptor, wait about 1 minute and then reconnect the battery or AC adaptor. Then about 1 minute later, turn on the power again. (Conducting the above operation while the card is being accessed may damage the data on the SD card.) ≥Does the grip belt not hide the remote controller receiver sensor? # Please take care so that the grip belt does not hide the remote controller receiver sensor. ≥Has the button-type battery of the remote control run out? # Replace it with a new button-type battery. (l 25) ≥If you set [SETUP] > [DISPLAY] > [OFF], indications other than warnings and date indications disappear. ≥Has the SD card's write protect switch been set to LOCK? # No recording is possible while the write protect switch is set to LOCK. (l 28) ≥Is the memory of the SD card full? # If there is no more available memory, free up some memory by deleting unnecessary scenes or use a new SD card. (l 34, 73, 75) ≥Is the unit set to recording mode? # No recording is possible if the mode dial is set to other than . ≥Is the card slot cover open? # If the card slot cover is open, this unit may not operate normally. Close the card slot cover. ≥Can the SD card be used for motion picture recording? # Use an SD card that can be used for motion picture recording. (l 27) 112

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
Others
112
Problem
Check points
This unit cannot be
operated though
powered up.
This unit does not
operate normally.
≥
Press the RESET button. (
l
115) If normal conditions are not
restored yet, remove the battery or AC adaptor, wait about 1 minute
and then reconnect the battery or AC adaptor. Then about 1 minute
later, turn on the power again. (Conducting the above operation
while the card is being accessed may damage the data on the
SD card.)
The remote control does
not function.
≥
Does the grip belt not hide the remote controller receiver sensor?
#
Please take care so that the grip belt does not hide the remote
controller receiver sensor.
≥
Has the button-type battery of the remote control run out?
#
Replace it with a new button-type battery. (
l
25)
A function indication
such as the remaining
time indication or the
elapsed time indication is
not shown.
≥
If you set [SETUP]
>
[DISPLAY]
>
[OFF], indications other than
warnings and date indications disappear.
Recording does not start
although power is
supplied to this unit and
the SD card is correctly
inserted.
≥
Has the SD card’s write protect switch been set to LOCK?
#
No recording is possible while the write protect switch is set to
LOCK. (
l
28)
≥
Is the memory of the SD card full?
#
If there is no more available memory, free up some memory by
deleting unnecessary scenes or use a new SD card. (
l
34, 73,
75)
≥
Is the unit set to recording mode?
#
No recording is possible if the mode dial is set to other than
.
≥
Is the card slot cover open?
#
If the card slot cover is open, this unit may not operate normally.
Close the card slot cover.
The unit arbitrarily stops
recording.
≥
Can the SD card be used for motion picture recording?
#
Use an SD card that can be used for motion picture recording.
(
l
27)