Ricoh Aficio MP C3500 Network Guide - Page 77

info, ipp, msh> ipp auth {basic|di

Get Ricoh Aficio MP C3500 PDF manuals and user guides View all Ricoh Aficio MP C3500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 77 highlights

Remote Maintenance by telnet ❖ Changing the Interface msh> ifconfig "interface" up ipp • You can specify either the Ethernet interface or IEEE 802.11b interface when using the op- Use the "ipp" command to view and configure IPP settings. tional IEEE 802.11b interface ❖ Viewing settings unit. You cannot specify the IEEE The following command displays the current IPP settings: 2 1394 interface. msh> ipp Note ❒ To get the above addresses, contact your network administrator. ❒ Use the default configuration if you cannot obtain setting addresses. ❒ The IP address, subnet mask and broadcast address are the same as that for the ethernet interface and IEEE 802.11b interface. ❒ When installing the optional 1394 Interface board, set the IP address and subnet mask so that it does not overlap with the ethernet interface or the IEEE 1394 interface. ❖ IPP timeout configuration Specify how many seconds the computer waits before canceling an interrupted print job. The time can be entered between 30 to 65535 seconds. msh> ipp timeout [30 - 65535] ❖ IPP user authorization configuration Use IPP user authorization to restrict users to print with IPP. The default is "off". msh> ipp auth {basic|digest|off} ❒ TCP/IP configuration is the same for both Ethernet and IEEE 802.11 interface. If interfaces are changed, the new interface inherits the configuration. ❒ Use "0x" as the initial two letters of a hexadecimal address. info Use the "info" command to display printer information such as paper tray, output tray, and printer language. ❖ Printer information display msh> info Reference p.86 "Getting Printer Information over the Network" • User authorization settings are "basic" and "digest". • If user authorization is specified, register a user name. You can register up to 10 users. ❖ IPP user configuration Configure IPP users according to the following messages: msh> ipp user The following message appears: msh> Input user number (1 to 10): Enter the number, user name, and password. msh> IPP user name:user1 msh> IPP password:******* After configuring the settings, the following message appears: User configuration changed. 69

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
Remote Maintenance by telnet
69
2
❖
Changing the Interface
msh> ifconfig “interface” up
•
You can specify either the Eth-
ernet interface or IEEE 802.11b
interface when using the op-
tional IEEE 802.11b interface
unit.
You cannot specify the IEEE
1394 interface.
Note
❒
To get the above addresses, contact
your network administrator.
❒
Use the default configuration if you
cannot obtain setting addresses.
❒
The IP address, subnet mask and
broadcast address are the same as
that for the ethernet interface and
IEEE 802.11b interface.
❒
When installing the optional 1394
Interface board, set the IP address
and subnet mask so that it does not
overlap with the ethernet interface
or the IEEE 1394 interface.
❒
TCP/IP configuration is the same
for both Ethernet and IEEE 802.11
interface. If interfaces are changed,
the new interface inherits the con-
figuration.
❒
Use "0x" as the initial two letters of
a hexadecimal address.
info
Use the "info" command to display
printer information such as paper
tray, output tray, and printer lan-
guage.
❖
Printer information display
msh> info
Reference
p.86 “Getting Printer Information
over the Network”
ipp
Use the “ipp” command to view and
configure IPP settings.
❖
Viewing settings
The following command displays
the current IPP settings:
msh> ipp
❖
IPP timeout configuration
Specify how many seconds the
computer waits before canceling
an interrupted print job. The time
can be entered between 30 to 65535
seconds.
msh> ipp timeout [30 - 65535]
❖
IPP user authorization configuration
Use IPP user authorization to re-
strict users to print with IPP. The
default is “off”.
msh> ipp auth {basic|di-
gest|off}
•
User authorization settings are
“basic” and “digest”.
• If user authorization is speci-
fied, register a user name. You
can register up to 10 users.
❖
IPP user configuration
Configure IPP users according to
the following messages:
msh> ipp user
The following message appears:
msh> Input user number (1
to 10):
Enter the number, user name, and
password.
msh> IPP user name:user1
msh> IPP password:*******
After configuring the settings, the
following message appears:
User configuration changed.