Seagate BlackArmor NAS 220 User Guide - Page 16

Setup Steps for Administrators, Installing the BlackArmor Server and Software

Get Seagate BlackArmor NAS 220 PDF manuals and user guides View all Seagate BlackArmor NAS 220 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Setup Steps for Administrators Setup Steps for Administrators If you are not a BlackArmor administrator, skip to page 26. Installing the BlackArmor Server and Software Before you begin: • Ensure that your computer meets the requirements listed on page 8. • Ensure that you have a solid, flat, stable surface for the server to sit on in an area with reliable ventilation. Ensure that the server's vents will not be covered or blocked and that the server is not placed near a heat source. Ensure that the server won't be in an area where liquids may be spilled on it. To install the BlackArmor server and software: 1. Use the Ethernet cable included in the kit to connect the BlackArmor server to a switch or router on your local network. Connect the Ethernet cable to the LAN port, as shown below: Step 2 Step 1 Figure 4: Connect power and network cables 2. Use the power adapter included in the kit to connect the BlackArmor server to a grounded power outlet. The server powers on automatically and the LED lights on the front panel of the server illuminate. 3. Insert the installation CD into your computer. The installation wizard opens automatically. Install both BlackArmor Discovery and BlackArmor Backup unless you are already using another backup software program. BlackArmor® NAS 220 User Guide (Version 2) 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
Setup Steps for Administrators
BlackArmor® NAS 220 User Guide (Version 2)
18
Setup Steps for Administrators
If you are not a BlackArmor administrator, skip to page 26.
Installing the BlackArmor Server and Software
Before you begin:
•
Ensure that your computer meets the requirements listed on page 8.
•
Ensure that you have a solid, flat, stable surface for the server to sit on in an area with
reliable ventilation. Ensure that the server’s vents will not be covered or blocked and that
the server is not placed near a heat source. Ensure that the server won’t be in an area
where liquids may be spilled on it.
To install the BlackArmor server and software:
1.
Use the Ethernet cable included in the kit to connect the BlackArmor server to a switch or
router on your local network. Connect the Ethernet cable to the LAN port, as shown
below:
Figure 4:
Connect power and network cables
2.
Use the power adapter included in the kit to connect the BlackArmor server to a grounded
power outlet.
The server powers on automatically and the LED lights on the front panel of the server
illuminate.
3.
Insert the installation CD into your computer.
The installation wizard opens automatically. Install both BlackArmor Discovery
and
BlackArmor Backup unless you are already using another backup software program.
Step 1
Step 2