Yamaha MOXF8 Owner's Manual - Page 55

4 In the Performance/Song/Pattern mode, set the output channel of the Audio signal for each part. When the output setting for the audio signal ("Mode" parameter) is set to "2StereoRec" in Step 1, you can change the audio output channel for each part. In the Performance mode, this parameter can be set in the [F4] USB I/O display of Common Edit. In the Song/Pattern mode, this parameter can be set in the [F4] USB I/O display of Mixing Common Edit. NOTE In the Voice mode, the audio output channel is fixed to USB 3/4. Setting up the DAW software on the computer 1 Set MIDI Thru to "on" on the DAW software. By setting MIDI Thru to "on," the MIDI data generated by playing the keyboard and transmitted to the computer will be returned back to the MOXF6/MOXF8. As shown in the example below, the MIDI data transmitted from the MOXF6/ MOXF8 then recorded to the computer via MIDI channel 1 will be returned back from the computer to the MOXF6/ MOXF8 via MIDI channel 3 according to the setting of the recording Track. As a result, the tone generator of the MOXF6/MOXF8 will sound the MIDI data generated by playing the keyboard as MIDI data from channel 3. USB TO HOST terminal Tone generator block (recognizing MIDI Channel 3 data) Local Control = off MOXF6/MOXF8 Keyboard (output via MIDI Channel 1) IN CH1 OUT CH3 Computer (Cubase, etc.) MIDI Thru = on Song playback from a computer using the MOXF6/MOXF8 as a tone generator The instructions below show how to use this instrument as a MIDI tone generator. In this case, actual MIDI sequence data is transmitted from DAW software on the computer, allowing you to avoid using software synths and save processing power on your computer. Setting up the MOXF6/MOXF8 1 Press the [SONG] or [PATTERN] button to enter the Song mode or Pattern mode. Quick Guide 2 Select the Song or Pattern to be edited. 3 Press the [MIXING] button to call up the Mixing display. 4 Set up the Mixing for parts 1 - 16 as necessary. From the Mixing display, you can select Voices and set various parameters such as pan, volume, balance between the Chorus/Reverb and dry sound, Insertion effect on/off and Arpeggio on/off. Setting up the DAW software on the computer 1 Set the MIDI output port of the Tracks for playing the MOXF6/MOXF8 to Port 1 of the "MOXF6/ MOXF8" 2 Enter the MIDI data to each Track of the DAW software on the computer. The tone generator settings of the part corresponding to the MIDI Track will be set in the Mixing mode on the MOXF6/ MOXF8. NOTE When using Cubase as the DAW, you can create an original Mixing setup of the MOXF6/MOXF8 from the MOXF6/MOXF8 Editor on your computer. The created Mixing setup can be saved as a Cubase Project file for future recall. Remote-controlling the software from the MOXF6/MOXF8 (Remote mode) The MOXF6/MOXF8 features a highly convenient Remote mode which lets you control the DAW software and software synthesizer on your computer via the panel operations of the MOXF6/MOXF8. For example, you can start/stop playback of the DAW software on the computer by using the Function buttons and control the song position on the DAW software by using the [DATA] dial, [INC] and [DEC] buttons instead of using the mouse or computer keyboard. Remote-controlling the software synthesizer Up to 50 Control Templates of VST Instruments can be stored to internal memory of this instrument. With these, you can use the MOXF6/MOXF8 to control various software synthesizers. Use the MOXF6/MOXF8 Remote Editor for editing the Control Template. NOTE To use the MOXF6/MOXF8 Remote Editor, you need to install the MOXF6/MOXF8 Remote Tools. The MOXF6/MOXF8 Remote Tools consists of two components: MOXF6/MOXF8 Remote Editor and MOXF6/MOXF8 Extension, which enables you to use the MOXF6/ MOXF8 along with Cubase series. 55 MOXF6/MOXF8 Owner's Manual