Yamaha MOXF8 Owner's Manual - Page 72

Removing the Module, Loosen both the screws.

Get Yamaha MOXF8 PDF manuals and user guides View all Yamaha MOXF8 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

Appendix 4-2 Press the top of the connector as shown, then push the connector firmly into the slot. Press this section lightly but firmly Removing the Module 1 Loosen both the screws. Serial No. seal 4-3 Tighten each screw of the Memory Module to each female screw of the MOXF with your hand as shown below. 5 Re-install the cover you removed in step 3, in reverse order. 6 Check that the installed Module or Modules are functioning properly. 6-1 Turn the MOXF right side up again so that the keyboard faces up then turn the power on. While launching, you will see a message indicating that the Flash Memory Module cannot be recognized. 6-2 Press the [FILE] button to enter the File mode then press the [F6] FLASH button. 6-3 Press the [SF1] Format button. 6-4 Press the [ENTER] button to execute the Format operation. 6-5 Check whether the Total size shown on the display is correct or not. NOTICE • If you cannot loosen the screw with your hand, use a Phillips screwdriver. In this case, be careful NOT to scratch the circuit board of the FL512M/FL1024M and MOXF. • Since the screws can be removed from the module, be careful NOT to drop them inside the instrument when loosening them. 2 Pull out the FL512M/FL1024M vertically. 3 Attach the cover to the bottom panel. Position the cover on the bottom panel aligning the screws with the screw holes, then tighten the screws with a Phillips screwdriver to fix the cover.  Rear side Bottom 72 MOXF6/MOXF8 Owner's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
MOXF6/MOXF8 Owner’s Manual
Appendix
72
4-2
Press the top of the connector as shown, then push the
connector firmly into the slot.
4-3
Tighten each screw of the Memory Module to each
female screw of the MOXF with your hand as shown
below.
5
Re-install the cover you removed in step 3, in
reverse order.
6
Check that the installed Module or Modules are
functioning properly.
6-1
Turn the MOXF right side up again so that the keyboard
faces up then turn the power on. While launching, you
will see a message indicating that the Flash Memory
Module cannot be recognized.
6-2
Press the [FILE] button to enter the File mode then
press the [F6] FLASH button.
6-3
Press the [SF1] Format button.
6-4
Press the [ENTER] button to execute the Format
operation.
6-5
Check whether the Total size shown on the display is
correct or not.
Removing the Module
1
Loosen both the screws.
NOTICE
•
If you cannot loosen the screw with your hand, use a Phillips
screwdriver. In this case, be careful NOT to scratch the circuit
board of the FL512M/FL1024M and MOXF.
•
Since the screws can be removed from the module, be careful NOT
to drop them inside the instrument when loosening them.
2
Pull out the FL512M/FL1024M vertically.
3
Attach the cover to the bottom panel.
Position the cover on the bottom panel aligning the screws
with the screw holes, then tighten the screws with a Phillips
screwdriver to fix the cover.
Press this section
lightly but firmly
Serial No. seal
Rear side
Bottom