Yamaha RX V1700 MCXSP10 Manual - Page 109

REMOTE CONTROL FEATURES Programming codes from other remote controls You can program remote control codes from other remote controls. Use the learn feature if you want to program functions not included in the basic operations covered by the remote control codes, or an appropriate remote control code is not available. You can program the function of other remote control to the buttons in the highlighted areas in the following illustration. The buttons can be programmed independently for each input area. POWER TV POWER AV STANDBY POWER XM AUDIO SEL SLEEP PHONO TUNER CD MULTI CH IN V-AUX/DOCK CBL/SAT MD/TAPE CD-R DTV VCR 1 DVR/VCR 2 DVD SELECT ++ TV VOL CH -- + VOLUME - AMP SOURCE TV TV MUTE TV INPUT MUTE LEVEL TITLE BAND PRESET/CH SET MENU MENU SRCH MODE PURE DIRECT ENTER AUDIO A-E/CAT. RETURN XM MEMORY PARAMETER STRAIGHT DISPLAY EFFECT CLASSICAL LIVE/CLUB ENTERTAIN MOVIE 1 2 3 4 STEREO SUR. DECODE SELECT EXTD SUR. 5 6 7 8 NIGHT ENHANCER 9 0 +10 ENT REC DISC SKIP OFF ON MACRO LEARN CLEAR RENAME (U.S.A. model) Note The remote control transmits infrared rays. If the other remote control also uses infrared rays, this remote control can learn most of its functions. However, you may not be able to program some special signals or extremely long transmissions. Refer to the operating instructions for the other remote control. 1 Set the operation mode selector to SOURCE and then press an input selector button or to select an input area. XM AMP SOURCE TV PHONO TUNER CD MULTI CH IN V-AUX/DOCK CBL/SAT MD/TAPE CD-R DTV VCR 1 DVR/VCR 2 DVD 2 Place this remote control about 5 to 10 cm (2 to 4 in) apart from the other remote control on a flat surface so that their infrared transmitters are aimed at each other. POWER TV XM PHONO TUNER POWER AV V-AUX/DOCK CBL/SAT MD/TAPE CD-R DTV STANDBY AUDIO SEL SLEEP CD VCR 1 DVR/VCR 2 DVD POWER MULTI CH IN SELECT (U.S.A. model) Other remote control 5 to 10 cm (2 to 4 in) 3 Press LEARN using a ballpoint pen or similar object. "LEARN" and the name of the selected input area (ex. "DVD") appear alternately in the display window on the remote control. LEARN Notes • Do not press and hold LEARN. If you hold it down for more than 3 seconds, the remote enters the remote control code setting mode. • If you do not complete each of the following steps within 30 seconds, the learning mode will be automatically canceled. In this case, start over from step 3. 4 Press the button for which you want to program the new function. "LEARN" appears in the display window on the remote control. POWER TV XM PHONO TUNER DTV ++ TV VOL -- TV MUTE LEVEL TITLE BAND A-E/CAT. RETURN XM MEMORY 1 5 9 REC DISC SKIP OFF ON POWER AV CH TV INPUT PRESET/CH ENTER 2 6 0 (U.S.A. model) V-AUX/DOCK CBL/SAT MD/TAPE CD-R STANDBY AUDIO SEL SLEEP CD VCR 1 DVR/VCR 2 DVD CLASSICAL LIVE/CLUB ENTERTAIN MOVIE STEREO SUR. DECODE SELECT EXTD SUR. + VOLUME - MUTE SET MENU MENU SRCH MODE PARAMETER STRAIGHT DISPLAY EFFECT 3 7 POWER MULTI CH IN SELECT PURE DIRECT NIGHT ENHANCER +10 MACRO LEARN CLEAR RENAME AMP SOURCE TV AUDIO 4 8 ENT Note Make sure that the operation mode selector is set to SOURCE. When you set the operation mode selector to AMP and program a remote control codes from other remote controls, the programmed key cannot operate the amplifier function of this unit. (U.S.A. model) ADVANCED OPERATION 105 En