Yamaha RX V1700 MCXSP10 Manual - Page 131

Problem, Cause, Remedy, Error message, DEVICE OVER, HDCP ERROR - hdmi not working

Get Yamaha RX V1700 - AV Receiver PDF manuals and user guides
UPC - 027108926186
View all Yamaha RX V1700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 131 highlights

■ Remote control TROUBLESHOOTING Problem The remote control does not work or function properly. The remote control does not learn new functions. Cause Remedy See page Wrong distance or angle. The remote control will function within a maximum range of 6 m (20 ft) and no more than 30 degrees off- 9 axis from the front panel. Direct sunlight or lighting (from an Reposition this unit. inverter type of fluorescent lamp, etc.) is striking the remote control sensor of this - unit. The batteries are weak. Replace all batteries. 9 The operation mode selector is set incorrectly. Set the operation mode selector correctly. When operating this unit, set it to the AMP position. When operating the component selected by the input selector button, set it to the SOURCE position. - When operating the TV set in the DTV or PHONO area, set it to the TV position. The remote control code was not correctly Set the remote control code correctly using set. "LIST OF REMOTE CONTROL CODES" at the end 103 of this manual. Try setting another code of the same manufacturer using "LIST OF REMOTE CONTROL CODES" at 103 the end of this manual. The library code of the remote control and Match the remote control ID of this unit with the the remote control ID of this unit do not corresponding remote control library code. match. 104, 118 Even if the remote control code is Program the necessary functions independently into correctly set, there are some models that the programmable buttons using the Learn feature. 105 do not respond to the remote control. The batteries of this remote control and/or Replace the batteries. the other remote control are too weak. 9 The distance between the two remote controls is too much or too little. Place the remote controls at the proper distance. 105 The signal coding or modulation of the Learning is not possible. other remote control is not compatible - with this remote control. Memory capacity is full. Delete other unnecessary functions to make room for the new functions. 110 ■ HDMI Error message DEVICE OVER HDCP ERROR Cause The number of the connected HDMI components is over the limit. HDCP authentication failed. Remedy Reduce the number of the connected HDMI components. Check that the connected HDMI components support the HDCP copy protection standards. See page - - ADDITIONAL INFORMATION 127 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
127
En
TROUBLESHOOTING
ADDITIONAL
INFORMATION
■
Remote control
■
HDMI
Problem
Cause
Remedy
See
page
The remote control
does not work or
function properly.
Wrong distance or angle.
The remote control will function within a maximum
range of 6 m (20 ft) and no more than 30 degrees off-
axis from the front panel.
9
Direct sunlight or lighting (from an
inverter type of fluorescent lamp, etc.) is
striking the remote control sensor of this
unit.
Reposition this unit.
—
The batteries are weak.
Replace all batteries.
9
The operation mode selector is set
incorrectly.
Set the operation mode selector correctly.
When operating this unit, set it to the AMP position.
When operating the component selected by the input
selector button, set it to the SOURCE position.
When operating the TV set in the DTV or PHONO
area, set it to the TV position.
—
The remote control code was not correctly
set.
Set the remote control code correctly using
“LIST OF REMOTE CONTROL CODES” at the end
of this manual.
103
Try setting another code of the same manufacturer
using “LIST OF REMOTE CONTROL CODES” at
the end of this manual.
103
The library code of the remote control and
the remote control ID of this unit do not
match.
Match the remote control ID of this unit with the
corresponding remote control library code.
104, 118
Even if the remote control code is
correctly set, there are some models that
do not respond to the remote control.
Program the necessary functions independently into
the programmable buttons using the Learn feature.
105
The remote control
does not learn new
functions.
The batteries of this remote control and/or
the other remote control are too weak.
Replace the batteries.
9
The distance between the two remote
controls is too much or too little.
Place the remote controls at the proper distance.
105
The signal coding or modulation of the
other remote control is not compatible
with this remote control.
Learning is not possible.
—
Memory capacity is full.
Delete other unnecessary functions to make room for
the new functions.
110
Error message
Cause
Remedy
See
page
DEVICE OVER
The number of the connected HDMI
components is over the limit.
Reduce the number of the connected HDMI
components.
—
HDCP ERROR
HDCP authentication failed.
Check that the connected HDMI components support
the HDCP copy protection standards.
—