Yamaha RX V1700 MCXSP10 Manual - Page 133

During AUTO SETUP, After AUTO SETUP

Get Yamaha RX V1700 - AV Receiver PDF manuals and user guides
UPC - 027108926186
View all Yamaha RX V1700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 133 highlights

During AUTO SETUP TROUBLESHOOTING Error message Cause Remedy E-1:NO FRONT SP E-2:NO SURR.SP E-3:NO PRNS. SP E-4:SBR->SBL E-5:NOISY E-6:CHECK SUR. E-7:NO MIC E-8:NO SIGNAL E-9:USER CANCEL E-10:INTERNAL ERROR Front L/R channel signals are not detected. A surround channel signal is not detected. A presence channel signal is not detected. Only right surround back channel signal is detected. Background noise is too loud. Surround back speakers are connected, though surround L/R speakers are not. The optimizer microphone was unplugged during the "AUTO SETUP" procedure. The optimizer microphone does not detect test tones. The "AUTO SETUP" procedure was cancelled due to user activity. An internal error occurred. Check the front L/R speaker connections. Check the surround speaker connections. Check the presence speaker connections. Connect the surround back speaker to the LEFT SURROUND BACK SPEAKERS terminal if you only have one surround back speaker. Try running "AUTO SETUP" in a quiet environment. Turn off noisy electric equipment like air conditioners or move them away from the optimizer microphone. Connect surround speakers when you use surround back speakers. Connect the supplied optimizer microphone to the OPTIMIZER MIC jack on the front panel. Check the microphone setting. Check the speaker connections and placement. Run "AUTO SETUP" again. Run "AUTO SETUP" again. After AUTO SETUP See page 14 14 14 14 - - 14 32 32 14 32 32 Warning message Cause Remedy W-1:OUT OF PHASE W-2:OVER 24m (80ft) W-3:LEVEL ERROR Speaker polarity is not correct. This message may appear depending on the speakers even when the speakers are connected correctly. The distance between the speaker and the listening position is over 24 m (80 ft). The difference of volume level among speakers is excessive. Check the speaker connections for proper polarity (+ or -). Bring the speaker closer to the listening position. Readjust the speaker installation so that all speakers are set in locations with similar conditions. Check the speaker connections. Use speakers of similar quality. Adjust the output volume of the subwoofer. Notes • If the "ERROR" or "WARNING" screens appears, check the cause of the problem, then run "AUTO SETUP" again. • If warning "W-1" appears, corrections are made, but they may not be optimal. • If warning "W-2" or "W-3" appears, no corrections are made. • If error "E-10" occurs repeatedly, please contact a qualified YAMAHA service center. See page 14 - - 14 - 32 ADDITIONAL INFORMATION 129 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
129
En
TROUBLESHOOTING
ADDITIONAL
INFORMATION
During AUTO SETUP
After AUTO SETUP
•
If the “ERROR” or “WARNING” screens appears, check the cause of the problem, then run “AUTO SETUP” again.
•
If warning “W-1” appears, corrections are made, but they may not be optimal.
•
If warning “W-2” or “W-3” appears, no corrections are made.
•
If error “E-10” occurs repeatedly, please contact a qualified YAMAHA service center.
Error message
Cause
Remedy
See
page
E-1:NO FRONT SP
Front L/R channel signals are not detected.
Check the front L/R speaker connections.
14
E-2:NO SURR.SP
A surround channel signal is not detected.
Check the surround speaker connections.
14
E-3:NO PRNS. SP
A presence channel signal is not detected.
Check the presence speaker connections.
14
E-4:SBR->SBL
Only right surround back channel signal is
detected.
Connect the surround back speaker to the
LEFT SURROUND BACK SPEAKERS
terminal if you only have one surround
back speaker.
14
E-5:NOISY
Background noise is too loud.
Try running “AUTO SETUP” in a quiet
environment.
—
Turn off noisy electric equipment like air
conditioners or move them away from the
optimizer microphone.
—
E-6:CHECK SUR.
Surround back speakers are connected,
though surround L/R speakers are not.
Connect surround speakers when you use
surround back speakers.
14
E-7:NO MIC
The optimizer microphone was unplugged
during the “AUTO SETUP” procedure.
Connect the supplied optimizer microphone
to the OPTIMIZER MIC jack on the front
panel.
32
E-8:NO SIGNAL
The optimizer microphone does not detect
test tones.
Check the microphone setting.
32
Check the speaker connections and
placement.
14
E-9:USER CANCEL
The “AUTO SETUP” procedure was
cancelled due to user activity.
Run “AUTO SETUP” again.
32
E-10:INTERNAL ERROR
An internal error occurred.
Run “AUTO SETUP” again.
32
Warning message
Cause
Remedy
See
page
W-1:OUT OF PHASE
Speaker polarity is not correct. This
message may appear depending on the
speakers even when the speakers are
connected correctly.
Check the speaker connections for proper
polarity (+ or –).
14
W-2:OVER 24m (80ft)
The distance between the speaker and the
listening position is over 24 m (80 ft).
Bring the speaker closer to the listening
position.
—
W-3:LEVEL ERROR
The difference of volume level among
speakers is excessive.
Readjust the speaker installation so that all
speakers are set in locations with similar
conditions.
—
Check the speaker connections.
14
Use speakers of similar quality.
—
Adjust the output volume of the subwoofer.
32
Notes