Yamaha YSP 4000 Owner's Manual - Page 45
AUTO SETUP, AUTO SETUP START, Press ENTER to start the AUTO SETUP
 |
UPC - 027108928760
View all Yamaha YSP 4000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 45 highlights
SETUP AUTO SETUP (IntelliBeam) 5 Press / to select BEAM+SOUND OPTIMZ, BEAM OPTIMZ only, or SOUND OPTIMZ only and then press ENTER. The following screen appears on your TV. ENTER ENTER 6 Check the following points once again before starting the AUTO SETUP procedure. • Is the IntelliBeam microphone firmly connected to this unit? • Is the IntelliBeam microphone placed in a proper location? • Are there any large obstacles in between the IntelliBeam microphone and the walls in your listening room? AUTO SETUP PREPARATION & CHECK Please connect the MIC. Please place the MIC at least 1.8m/6ft away from the YSP unit. The MIC should be set at ear level when seated. Measurement takes about 3min. After [ENTER] is pressed, please leave the room. [ENTER]:Start [RETURN]:Cancel 7 Press ENTER to start the AUTO SETUP procedure. The following screen appears on your TV and the AUTO SETUP procedure starts in 10 seconds. Leave the room quietly before starting the AUTO SETUP procedure. ENTER BEAM+SOUND OPTIMZ (Beam optimization and sound optimization) Use to optimize the beam angle, delay, volume, and quality so that the parameters best match your listening environment. It is recommended that you should select this optimization feature in the following cases: • If you make settings for the first time. • If the unit has been relocated. • If your listening room has been restructured. • If the objects in your listening room (furniture, etc.) have been rearranged. This menu takes about three minutes. BEAM OPTIMZ only (Beam optimization only) Use to optimize the beam angle so that the parameter best matches your listening environment. This menu takes about one minute. SOUND OPTIMZ only (Sound optimization only) Use to optimize the beam delay, volume, and quality so that the parameters best match your listening environment. It is recommended that you should select this optimization feature in the following cases: • If you have opened or closed the curtains in your listening room before using this unit. • If you have manually set the beam angle. This menu takes about two minutes. AUTO SETUP START Will begin in 10sec Please leave the room **-------[RETURN]:Cancel ← Flashes If an error occurs, an error buzzer is played and an error message is displayed. See "Error messages for AUTO SETUP" on page 43 for a complete list of error messages and their proper remedies. Follow the instructions and perform the AUTO SETUP procedure again. Note You must optimize the beam angle in the BEAM OPTIMZ only procedure before starting the SOUND OPTIMZ only procedure. English 41 En
-
1 -
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40 -
41 -
42 -
43 -
44 -
45 -
46 -
47 -
48 -
49 -
50 -
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
 |
 |
