3Com 3C780 User Guide - Page 137

set boot

Get 3Com 3C780 - LinkBuilder FDDI Base Unit PDF manuals and user guides
UPC - 662705029917
View all 3Com 3C780 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 137 highlights

Commands C-3 You can also enter the baud rate on the same line with the set baud command, as shown below: set baud 4800 [Enter] set boot Syntax set boot [method | filename | server] Simplified Syntax set boot method set boot filename set boot server Description The set boot method command allows you to select the method to use when downloading an image to the flash EPROM. The available options are: LOCAL Loads and runs the flash EPROM code (default) TFTP Uses TFTP and local configuration parameters to load a new image over the network The set boot filename command allows you to set the filename of the software image to be loaded when using TFTP. The set boot server command allows you to set the IP address of the boot server. Examples An example of each option is shown below: s When you enter the set boot method command, you are prompted to select the server location of the information to be downloaded, as shown below: Select one of the following: 1. LOCAL 2. TFTP Boot Method?

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
C-3
Commands
You can also enter the baud rate on the same line with the
set baud
command, as
shown below:
set baud 4800 [Enter]
set boot
Syntax
set boot [method | filename | server]
Simplified Syntax
set boot method
set boot filename
set boot server
Description
The
set boot method
command allows you to select the method to use when
downloading an image to the flash EPROM.
The available options are:
LOCAL
Loads and runs the flash EPROM code (default)
TFTP
Uses TFTP and local configuration parameters to load a new
image over the network
The
set boot filename
command allows you to set the filename of the software
image to be loaded when using TFTP.
The
set boot server
command allows you to set the IP address of the boot server.
Examples
An example of each option is shown below:
■
When you enter the
set boot method
command, you are prompted to select
the server location of the information to be downloaded, as shown below:
Select one of the following:
1. LOCAL
2. TFTP
Boot Method?