3Com 3C780 User Guide - Page 88

Setting Up the Hub

Get 3Com 3C780 - LinkBuilder FDDI Base Unit PDF manuals and user guides
UPC - 662705029917
View all 3Com 3C780 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 88 highlights

Setting Up the Hub 4-1 Chapter 4 Setting Up the Hub The LinkBuilder FDDI Workgroup Hub is shipped ready to plug in and use without the need to change any parameters. In all probability, however, you will want to make a number of changes to adapt the hub to your network environment. This chapter discusses how to use the management console commands to set up the hub and make any desired parameter changes. Topics include: s Using commands to: - Set addresses - Set the password - Set attachment port configuration - Set station management parameters s Downloading new images Commands The commands supported by the management console command mode and the primitive console command mode enable you to set and display the basic parameters needed to configure and operate the hub. The commands are grouped into three functional categories that are defined below: s Use set commands to institute various functions. s Use show commands to display default parameter settings and reflect any changes you make. s Use miscellaneous commands to support various diagnostic and troubleshooting functions.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
Chapter 4
Setting Up the Hub
The LinkBuilder FDDI Workgroup Hub is shipped ready to plug in and use
without the need to change any parameters.
In all probability, however, you
will want to make a number of changes to adapt the hub to your network
environment.
This chapter discusses how to use the management console
commands to set up the hub and make any desired parameter changes.
Topics
include:
■
Using commands to:
–
Set addresses
–
Set the password
–
Set attachment port configuration
–
Set station management parameters
■
Downloading new images
Commands
The commands supported by the management console command mode and the
primitive console command mode enable you to set and display the basic
parameters needed to configure and operate the hub.
The commands are
grouped into three functional categories that are defined below:
■
Use
set
commands to institute various functions.
■
Use
show
commands to display default parameter settings and reflect any
changes you make.
■
Use miscellaneous commands to support various diagnostic and
troubleshooting functions.