Bosch NBN-498-11P Operation Manual - Page 85

Destination IP address

Get Bosch NBN-498-11P PDF manuals and user guides View all Bosch NBN-498-11P manuals
Add to My Manuals
Save this manual to your list of manuals

Page 85 highlights

Dinion2X IP Camera Advanced Mode | en 85 system such as VIDOS or Bosch Video Management System. The camera connects to all remote stations protected by the same general password. To define a general password: 1. Select 10 in the Number of destination IP address list box. 2. Enter 0.0.0.0 in the Destination IP address field. 3. Enter the password in the Destination password field. 4. Set the user password of all the remote stations to be accessed using this password. Setting destination 10 to the IP-address 0.0.0.0 overrides its function as the tenth address to try. Video transmission If the device is operated behind a firewall, select TCP (HTTP port) as the transfer protocol. For use in a local network, select UDP. Please note that in some circumstances, in the event of an alarm, a larger bandwidth must be available on the network for additional video images (if Multicast operation is not possible). To enable Multicast operation, select the UDP option for the Video transmission parameter here and on the Network page. Remote port Select a browser port, depending on the network configuration. The ports for HTTPS connections are only available if the On option in SSL encryption is selected. Video output If it is known which device is being used as the receiver, select the analog video output to which the signal should be switched. If the destination device is unknown, it is advisable to select the First available option. In this case, the image is placed on the first free video output. This is an output on which there is no signal. The connected monitor only displays images when an alarm is triggered. If a particular video output is selected and a split image is set for this output on the receiver, select the decoder from Decoder in the receiver that is to be used to display the alarm image. Refer to the destination device Bosch Security Systems Installation and Operation Manual AR18-10-B006 | v1.1 | 2010.06

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
Dinion2X IP Camera
Advanced Mode | en
85
Bosch Security Systems
Installation and Operation Manual
AR18-10-B006 | v1.1 | 2010.06
system such as VIDOS or Bosch Video Management System.
The camera connects to all remote stations protected by the
same general password. To define a general password:
1.
Select 10 in the
Number of destination IP address
list
box.
2.
Enter 0.0.0.0 in the
Destination IP address
field.
3.
Enter the password in the
Destination password
field.
4.
Set the user password of all the remote stations to be
accessed using this password.
Setting destination 10 to the IP-address 0.0.0.0 overrides its
function as the tenth address to try.
Video transmission
If the device is operated behind a firewall, select
TCP (HTTP
port)
as the transfer protocol. For use in a local network, select
UDP
.
Please note that in some circumstances, in the event of an
alarm, a larger bandwidth must be available on the network for
additional video images (if Multicast operation is not possible).
To enable Multicast operation, select the
UDP
option for the
Video transmission
parameter here and on the
Network
page.
Remote port
Select a browser port, depending on the network configuration.
The ports for HTTPS connections are only available if the
On
option in
SSL encryption
is selected.
Video output
If it is known which device is being used as the receiver, select
the analog video output to which the signal should be switched.
If the destination device is unknown, it is advisable to select the
First available
option. In this case, the image is placed on the
first free video output. This is an output on which there is no
signal. The connected monitor only displays images when an
alarm is triggered. If a particular video output is selected and a
split image is set for this output on the receiver, select the
decoder from
Decoder
in the receiver that is to be used to
display the alarm image. Refer to the destination device