Brother International TD-4750TNWB Users Guide - Page 31

Ribbon and Gap/Black Mark Sensor Calibration, Self-Test, and Entering Dump Mode, Feed/Pause

Get Brother International TD-4750TNWB PDF manuals and user guides View all Brother International TD-4750TNWB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

5.1.1 Ribbon and Gap/Black Mark Sensor Calibration The Gap/Black Mark Sensors' sensitivity should be calibrated when:  You purchase a new printer.  You change label stock.  The label printer initializes. To calibrate the Ribbon and Gap/Black Mark Sensors: 1. Turn off the printer. 2. Press and hold the Feed/Pause button, and then turn on the printer. 3. Release the button when the LED is flashing in red/amber. Note  The LED color will change as follows: Amber (lit)  red/amber (5 times)  amber (5 times)  green/red (5 times)  green (5 times)  red (5 times)  green (lit)  To select the sensor for calibration, send the correct command to the printer:  For the Gap Sensor: send the GAP command  For the Black Mark Sensor: send the BLINE command For more information about the available commands, see the FBPL Command Reference Manual on your model's Manuals page at support.brother.com. 5.1.2 Gap/Black Mark Sensor Calibration, Self-Test, and Entering Dump Mode Calibrate the Gap or Black Mark Sensor if the sensor's settings used in the last print job are not suitable for the current print job. During the calibration of the Gap/Black Mark Sensor, the printer detects the label length, prints the internal configuration (self-test), and then enters Dump Mode. To calibrate the Gap/Black Mark Sensor: 1. Turn off the printer. 2. Press and hold the Feed/Pause button, and then turn on the printer. 3. Release the button when the LED is flashing in amber. Note The LED color will change as follows: Amber (lit)  red/amber (5 times)  amber (5 times)  green/red (5 times)  green (5 times)  red (5 times)  green (lit) 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
27
5.1.1
Ribbon and Gap/Black Mark Sensor Calibration
The Gap/Black Mark Sensors’ sensitivity should be calibrated when:
You purchase a new printer.
You change label stock.
The label printer initializes.
To calibrate the Ribbon and Gap/Black Mark Sensors:
1. Turn off the printer.
2. Press and hold the
Feed/Pause
button, and then turn on the printer.
3. Release the button when the LED is flashing in red/amber.
Note
The LED color will change as follows:
Amber (lit)
red/amber (5 times)
amber (5 times)
green/red (5 times)
green (5 times)
red (5 times)
green (lit)
To select the sensor for calibration, send the correct command to the printer:
For the Gap Sensor: send the GAP command
For the Black Mark Sensor: send the BLINE command
For more information about the available commands, see the
FBPL Command Reference
Manual
on your model's
Manuals
page at
support.brother.com
.
5.1.2
Gap/Black Mark Sensor Calibration, Self-Test, and Entering Dump
Mode
Calibrate the Gap or Black Mark Sensor if the sensor's settings used in the last print job are not
suitable for the current print job. During the calibration of the Gap/Black Mark Sensor, the
printer detects the label length, prints the internal configuration (self-test), and then enters
Dump Mode.
To calibrate the Gap/Black Mark Sensor:
1. Turn off the printer.
2. Press and hold the
Feed/Pause
button, and then turn on the printer.
3. Release the button when the LED is flashing in amber.
Note
The LED color will change as follows:
Amber (lit)
red/amber (5 times)
amber (5 times)
green/red (5 times)
green (5 times)
red (5 times)
green (lit)