Home » Brother International Manuals » Label Makers » Brother International TD-4750TNWB » Manual Viewer

Brother International TD-4750TNWB Users Guide - Page 60

RFID Calibration (available for TD-4650TNWBR and TD-4750TNWBR only)

View all Brother International TD-4750TNWB manuals

Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

8.2 RFID Calibration (available for TD-4650TNWBR and TD-4750TNWBR only) 8.2.1 Select the Antenna Position Check the label to determine the best position for the antenna, locating the antenna loop within the tag. In most cases, the antenna loop is directly above or below the chip. The loop may be off to one side of the chip in some tags. Open the Roll Compartment Cover. Move the Antenna Slide so that the Position Indicator aligns with the loop in the tag. Antenna Slide Position Indicator Numbered Position Strip 8.2.2 RFID Calibration Procedure Note For optimal calibration results, perform Media Calibration before RFID Calibration. Make sure you correctly install both the ribbon and the label roll. 1. Perform Media Auto Calibration:  Using the LCD menu: a. Load the RFID media into the printer. b. (Thermal transfer only) Load the ribbon into the printer. c. Select the Menu . 56

Section	Page
User's Guide TD-4650TNWB/4650TNWBR/TD-4750TNWB/4750TNWBR	1
Contents	3
1. Introduction	5
1.1 Product Introduction	5
1.2 Additional Product Reference	5
2. Operations Overview	6
2.1 Unpack the printer and check the components	6
2.2 Printer Overview	7
2.2.1 Front View	7
2.2.2 Interior View	8
2.2.3 Rear View	9
2.3 Connect the Power Cord	10
2.4 Control Panel	11
2.5 LED Indicator	12
3. Set Up Your Printer	13
3.1 Load the Ribbon	13
3.2 Load the Media	15
3.2.1 Load Label Roll	15
3.2.2 Install the External Roll Holder (Optional)	18
3.2.3 Install the Label Roll When Using the Cutter Module (Dealers only)	20
3.2.4 Install the Label Roll When Using the Label Peeler (Dealers only)	22
4. Printing	25
4.1 Printer Driver Installation	25
4.1.1 USB Connection (Windows/Mac/Linux)	25
4.1.2 Bluetooth Connection (Windows)	26
4.1.3 Wi-Fi Network Connection (Windows)	26
4.1.4 Wired Network Connection (Windows)	27
4.2 Creating and Printing Labels Using BarTender	28
5. Operation	30
5.1 Power-on Utilities	30
5.1.1 Ribbon and Gap/Black Mark Sensor Calibration	31
5.1.2 Gap/Black Mark Sensor Calibration, Self-Test, and Entering Dump Mode	31
5.1.3 Printer Initialization	35
5.1.4 Media Sensor Calibration (for the Black Mark Sensor)	36
5.1.5 Media Sensor Calibration (for the Gap Sensor)	36
5.1.6 Skip the AUTO.BAS program	36
6. LCD Overview	37
6.1 Access the Main Menu	37
6.2 Main Menu Overview	38
6.3 Setting Menu	39
6.3.1 FBPL Settings	39
6.3.2 ZPL2 Settings	41
6.4 Sensor Settings	43
6.5 Interface Settings	44
6.5.1 Serial Communication Settings	45
6.5.2 Ethernet Settings	45
6.5.3 Wi-Fi Settings	46
6.5.4 Bluetooth Settings	47
6.5.5 RFID (Radio Frequency Identification) Settings	48
6.6 Advanced Settings	54
6.7 File Manager	55
6.8 Diagnostic Functions	56
7. Brother Printer Management Tool (BPM)	57
7.1 Start the BPM	57
7.2 Auto-Calibrating the Media Sensor using the BPM	58
8. Setting up the RFID	59
8.1 Introduction	59
8.2 RFID Calibration (available for TD-4650TNWBR and TD-4750TNWBR only)	60
8.2.1 Select the Antenna Position	60
8.2.2 RFID Calibration Procedure	60
9. Product Specifications	63
10. Troubleshooting	66
10.1 Common Problems	66
10.2 RFID Error Messages	69