Brother International TD-4750TNWB Users Guide - Page 36

Media Sensor Calibration (for the Black Mark Sensor), 5.1.6 Skip the AUTO.BAS program

Get Brother International TD-4750TNWB PDF manuals and user guides View all Brother International TD-4750TNWB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

5.1.4 Media Sensor Calibration (for the Black Mark Sensor) 1. Turn off the printer. 2. Press and hold the Feed/Pause button, and then turn on the printer. 3. Release the button after the green/red LED flashes five times and the LED is lit in green. Note The LED color will change as follows: Amber (lit)  red/amber (5 times)  amber (5 times)  green/red (5 times)  green (5 times)  red (5 times)  green (lit) 5.1.5 Media Sensor Calibration (for the Gap Sensor) 1. Turn off the printer. 2. Press and hold the Feed/Pause button, and then turn on the printer. 3. Release the button after the green LED flashes five times and the LED is lit in red. Note The LED color will change as follows: Amber (lit)  red/amber (5 times)  amber (5 times)  green/red (5 times)  green (5 times)  red (5 times)  green (lit) 5.1.6 Skip the AUTO.BAS program You can upload the AUTO.BAS program to the printer's flash memory so that it runs automatically at startup, but if you do not want it to run automatically, follow these steps: 1. Turn off the printer. 2. Press the Feed/Pause button, and then turn on the printer. 3. Release the button when the LED is lit in green. Note The LED color will change in the following order: Amber (lit)  red/amber (5 times)  amber (5 times)  green/red (5 times)  green (5 times)  red (5 times)  green (lit) 4. The printer will start without running the AUTO.BAS program. 32

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
32
5.1.4
Media Sensor Calibration (for the Black Mark Sensor)
1. Turn off the printer.
2. Press and hold the
Feed/Pause
button, and then turn on the printer.
3. Release the button after the green/red LED flashes five times and the LED is lit in green.
Note
The LED color will change as follows:
Amber (lit)
red/amber (5 times)
amber (5 times)
green/red (5 times)
green (5 times)
red (5 times)
green (lit)
5.1.5
Media Sensor Calibration (for the Gap Sensor)
1. Turn off the printer.
2. Press and hold the
Feed/Pause
button, and then turn on the printer.
3. Release the button after the green LED flashes five times and the LED is lit in red.
Note
The LED color will change as follows:
Amber (lit)
red/amber (5 times)
amber (5 times)
green/red (5 times)
green (5 times)
red (5 times)
green (lit)
5.1.6 Skip the AUTO.BAS program
You can upload the AUTO.BAS program to the printer's flash memory so that it runs
automatically at startup, but if you do not want it to run automatically, follow these steps:
1. Turn off the printer.
2. Press the
Feed/Pause
button, and then turn on the printer.
3. Release the button when the LED is lit in green.
Note
The LED color will change in the following order:
Amber (lit)
red/amber (5 times)
amber (5 times)
green/red (5 times)
green (5 times)
red (5 times)
green (lit)
4. The printer will start without running the AUTO.BAS program.