Home » Brother International Manuals » Label Makers » Brother International TD-4750TNWB » Manual Viewer

Brother International TD-4750TNWB Users Guide - Page 45

Serial Communication Settings, 6.5.2 Ethernet Settings, Baud Rate, Parity, Data Bits, Stop Bits

View all Brother International TD-4750TNWB manuals

Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

6.5.1 Serial Communication Settings Set the printer RS-232 settings. Baud Rate Menu Interface Serial Parity Data Bits Stop Bit(s) Setting Baud Rate Parity Data Bits Stop Bit(s) Set the RS-232 Baud rate. Description Set the RS-232 Parity. Set the RS-232 Data bits. Set the RS-232 Stop bits. 1200 bps 2400 bps 4800 bps 9600 bps 19200 bps 38400 bps 57600 bps 115200 bps None Odd Even 7 8 1 2 6.5.2 Ethernet Settings Configure your printer's Ethernet (wired) connection and check its status. When the Ethernet is connected, the Ethernet icon and IP address are displayed on the LCD as shown below. 41

Section	Page
User's Guide TD-4650TNWB/4650TNWBR/TD-4750TNWB/4750TNWBR	1
Contents	3
1. Introduction	5
1.1 Product Introduction	5
1.2 Additional Product Reference	5
2. Operations Overview	6
2.1 Unpack the printer and check the components	6
2.2 Printer Overview	7
2.2.1 Front View	7
2.2.2 Interior View	8
2.2.3 Rear View	9
2.3 Connect the Power Cord	10
2.4 Control Panel	11
2.5 LED Indicator	12
3. Set Up Your Printer	13
3.1 Load the Ribbon	13
3.2 Load the Media	15
3.2.1 Load Label Roll	15
3.2.2 Install the External Roll Holder (Optional)	18
3.2.3 Install the Label Roll When Using the Cutter Module (Dealers only)	20
3.2.4 Install the Label Roll When Using the Label Peeler (Dealers only)	22
4. Printing	25
4.1 Printer Driver Installation	25
4.1.1 USB Connection (Windows/Mac/Linux)	25
4.1.2 Bluetooth Connection (Windows)	26
4.1.3 Wi-Fi Network Connection (Windows)	26
4.1.4 Wired Network Connection (Windows)	27
4.2 Creating and Printing Labels Using BarTender	28
5. Operation	30
5.1 Power-on Utilities	30
5.1.1 Ribbon and Gap/Black Mark Sensor Calibration	31
5.1.2 Gap/Black Mark Sensor Calibration, Self-Test, and Entering Dump Mode	31
5.1.3 Printer Initialization	35
5.1.4 Media Sensor Calibration (for the Black Mark Sensor)	36
5.1.5 Media Sensor Calibration (for the Gap Sensor)	36
5.1.6 Skip the AUTO.BAS program	36
6. LCD Overview	37
6.1 Access the Main Menu	37
6.2 Main Menu Overview	38
6.3 Setting Menu	39
6.3.1 FBPL Settings	39
6.3.2 ZPL2 Settings	41
6.4 Sensor Settings	43
6.5 Interface Settings	44
6.5.1 Serial Communication Settings	45
6.5.2 Ethernet Settings	45
6.5.3 Wi-Fi Settings	46
6.5.4 Bluetooth Settings	47
6.5.5 RFID (Radio Frequency Identification) Settings	48
6.6 Advanced Settings	54
6.7 File Manager	55
6.8 Diagnostic Functions	56
7. Brother Printer Management Tool (BPM)	57
7.1 Start the BPM	57
7.2 Auto-Calibrating the Media Sensor using the BPM	58
8. Setting up the RFID	59
8.1 Introduction	59
8.2 RFID Calibration (available for TD-4650TNWBR and TD-4750TNWBR only)	60
8.2.1 Select the Antenna Position	60
8.2.2 RFID Calibration Procedure	60
9. Product Specifications	63
10. Troubleshooting	66
10.1 Common Problems	66
10.2 RFID Error Messages	69