Cisco 7600 SIP 200 Hardware Installation Guide - Page 145

Deactivation of a SIP Configuration Example

Get Cisco 7600 SIP 200 - SPA Interface Processor 200 PDF manuals and user guides
UPC - 746320961286
View all Cisco 7600 SIP 200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 145 highlights

Chapter 5 Installing and Removing a SIP Online Insertion and Removal Deactivation of a SIP Configuration Example Deactivate a SIP when you want to perform OIR of the SIP. The following example deactivates the SIP that is installed in slot 5 of the router, its SPAs, and all of the interfaces. The corresponding console messages are shown: Router# configure terminal Router(config)# no power enable module 5 1w4d: %OIR-6-REMCARD: Card removed from slot 5, interfaces disabled 1w4d: %C6KPWR-SP-4-DISABLED: power to module in slot 5 set off (admin request) Activation of a SIP Configuration Example Activate a SIP if you have previously deactivated it. If you did not deactivate the SPAs, the SPAs automatically reactivate with reactivation of the SIP. The following example activates the SIP that is installed in slot 5 of the router, its SPA, and all of the interfaces (as long as the hw-module subslot shutdown command was not issued to also deactivate the SPA): Router# configure terminal Router(config)# power enable module 5 Notice that there are no corresponding console messages shown with activation. If you re-enter the power enable module command, a message is displayed indicating that the module is already enabled: Router(config)# power enable module 5 % module is already enabled Deactivation of a SPA Configuration Example Deactivate a SPA when you want to perform OIR of that SPA. The following example deactivates the SPA (and its interfaces) that is installed in subslot 0 of the SIP located in slot 2 of the router and removes power to the SPA. Notice that no corresponding console messages are shown: Router# configure terminal Router(config)# hw-module subslot 2/0 shutdown unpowered Activation of a SPA Configuration Example Activate a SPA if you have previously deactivated it. If you have not deactivated a SPA and its interfaces during OIR of a SIP, then the SPA is automatically reactivated upon reactivation of the SIP. The following example activates the SPA that is installed in slot 2 of the router and all of its interfaces. Router# configure terminal Router(config)# no hw-module subslot 2/0 shutdown Router# OL-5052-14 Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 5-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
5-7
Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-14
Chapter 5
Installing and Removing a SIP
Online Insertion and Removal
Deactivation of a SIP Configuration Example
Deactivate a SIP when you want to perform OIR of the SIP. The following example deactivates the SIP
that is installed in slot 5 of the router, its SPAs, and all of the interfaces. The corresponding console
messages are shown:
Router#
configure terminal
Router(config)#
no power enable module 5
1w4d: %OIR-6-REMCARD: Card removed from slot 5, interfaces disabled
1w4d: %C6KPWR-SP-4-DISABLED: power to module in slot 5 set off (admin request)
Activation of a SIP Configuration Example
Activate a SIP if you have previously deactivated it. If you did not deactivate the SPAs, the SPAs
automatically reactivate with reactivation of the SIP.
The following example activates the SIP that is installed in slot 5 of the router, its SPA, and all of the
interfaces (as long as the
hw-module subslot shutdown
command was not issued to also deactivate
the SPA):
Router#
configure terminal
Router(config)#
power enable module 5
Notice that there are no corresponding console messages shown with activation. If you re-enter the
power enable module
command, a message is displayed indicating that the module is already
enabled:
Router(config)#
power enable module 5
% module is already enabled
Deactivation of a SPA Configuration Example
Deactivate a SPA when you want to perform OIR of that SPA. The following example deactivates the
SPA (and its interfaces) that is installed in subslot 0 of the SIP located in slot 2 of the router and removes
power to the SPA. Notice that no corresponding console messages are shown:
Router#
configure terminal
Router(config)#
hw-module subslot 2/0 shutdown unpowered
Activation of a SPA Configuration Example
Activate a SPA if you have previously deactivated it. If you have not deactivated a SPA and its interfaces
during OIR of a SIP, then the SPA is automatically reactivated upon reactivation of the SIP.
The following example activates the SPA that is installed in slot 2 of the router and all of its interfaces.
Router#
configure terminal
Router(config)#
no hw-module subslot 2/0 shutdown
Router#