Cisco 7600 SIP 200 Hardware Installation Guide - Page 164

Packing a SPA for Shipment, Packing a SIP for Shipment

Get Cisco 7600 SIP 200 - SPA Interface Processor 200 PDF manuals and user guides
UPC - 746320961286
View all Cisco 7600 SIP 200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 164 highlights

Packing a SPA for Shipment Chapter 7 Troubleshooting the Installation Packing a SPA for Shipment This section provides step-by-step instructions for packing a SPA and the cable-management brackets for shipment. Before beginning this procedure, you should have the following original Cisco Systems packaging materials: • Thermoform container (transparent plastic-molded clamshell) • Carton Caution Use Cisco Systems original packaging for the shipment of all SPAs and cable-management brackets. Failure to properly use Cisco Systems packaging can result in damage or loss of product. Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself. Statement 94 Note These instructions assume that the SPA and cable-management brackets have been removed from the router according to the recommended procedures specified in this guide. To pack a SPA and the cable-management brackets for shipment, follow these steps: Step 1 Open the thermoform container and place the SPA and each of the cable-management brackets into the appropriate cavities. Caution Always handle the SPA by the carrier edges and handle; never touch the SPA components or connector pins. Step 2 Step 3 Step 4 Step 5 Step 6 Close the thermoform container. Be sure to lock the snaps securely. Check that the thermoform container is fully closed. Apply tape or a label closure over the opening to ensure that the container stays closed during shipping. Place the thermoform container into the carton. Close the carton. Apply tape over the carton flap to ensure that the carton stays closed during shipping. Packing a SIP for Shipment This section provides step-by-step instructions for packing a SIP for shipment. Before beginning this procedure, you should have the following original Cisco Systems packaging materials: • Static shielding bag • Smaller inner carton • Larger exterior carton Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide 7-8 OL-5052-14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
7-8
Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide
OL-5052-14
Chapter 7
Troubleshooting the Installation
Packing a SPA for Shipment
Packing a SPA for Shipment
This section provides step-by-step instructions for packing a SPA and the cable-management brackets
for shipment. Before beginning this procedure, you should have the following original Cisco Systems
packaging materials:
•
Thermoform container (transparent plastic-molded clamshell)
•
Carton
Caution
Use Cisco Systems original packaging for the shipment of all SPAs and cable-management brackets.
Failure to properly use Cisco Systems packaging can result in damage or loss of product.
Warning
During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly
touch the backplane with your hand or any metal tool, or you could shock yourself.
Statement 94
Note
These instructions assume that the SPA and cable-management brackets have been removed from the
router according to the recommended procedures specified in this guide.
To pack a SPA and the cable-management brackets for shipment, follow these steps:
Step 1
Open the thermoform container and place the SPA and each of the cable-management brackets into the
appropriate cavities.
Caution
Always handle the SPA by the carrier edges and handle; never touch the SPA components or connector
pins.
Step 2
Close the thermoform container. Be sure to lock the snaps securely.
Step 3
Check that the thermoform container is fully closed. Apply tape or a label closure over the opening to
ensure that the container stays closed during shipping.
Step 4
Place the thermoform container into the carton.
Step 5
Close the carton.
Step 6
Apply tape over the carton flap to ensure that the carton stays closed during shipping.
Packing a SIP for Shipment
This section provides step-by-step instructions for packing a SIP for shipment. Before beginning this
procedure, you should have the following original Cisco Systems packaging materials:
•
Static shielding bag
•
Smaller inner carton
•
Larger exterior carton